Код ошибки 84ff

Модераторы: Trinity admin`s, Free-lance moderator`s

← Вернуться в раздел «Драйверы и прошивки BIOS»

Страницы: 1

Предыдущая тема: прошивки для transcend t.sonic 620

Форум Ru-Board.club — поднят 15-09-2016 числа. Цель — сохранить наследие старого Ru-Board, истории становления российского интернета. Сделано для людей.

Здравствуйте.
Есть плата, S5000PSL
После загрузки БИОСА (EFI), сразу открывается вкладка:
Error Manager, с сообщением:
ERROR — 84F2 : BaseBoard management controller failed to respond

Под ДОСом, при попытках обновиться, вот такие ошибки:

у BMC — «ERROR 017 : Invalid Argument»
а у FRUSDR — «Error, could not detect BMC through ISA/SMBUS driver»

А когда пытаюсь обновиться Intel Deployment Assistant»ом и указываю, что прошивка лежит на USB,
вываливается ошибка «*ERROR* Failed to communicate with BMC»

При этом, BIOS уже перепрошит на 101 версию, но если зайти в Server Managment -> System Information, то там пусто.
Только строка UUID заполнена.

Это не единичный случай, в сети есть обсуждения этой проблемы, но решения нет.
Народ или боится или не может или не умеет или не хочет, в общем советы обрываются на середине пути.

В моей же ситуации — готов идти до конца, т.к назад дороги нет! ))
Есть огромное желание (и относительно прямые руки), привести плату в порядок.
Плюс ко всему, есть вторая плата, с которой можно снять дамп.

Просто мне не понятно, с чего начать и в какую сторону двигаться.

P.S. запустил fwpiaupd с параметром (-?) и там видно, что BMC можно полностью перепрошить, но вот не могу понять,
где взять БутБлок и как грамотно составить параметры прошивки.

Буду благодарен за любые мнения и советы! (а то уже мозг кипит)

приаттачил пару скринов и архив с прошивкой.

I purchased a pristine board in the box and wanted to use it for a home NAS eventually, but in the meantime I thought i could use it for something else. So I have installed it into a Fractal Design case with the necessary hardware to boot etc.

I was successful in testing several different types of OS. I can install almost any Linux Version without issue, both x86 and x64. Everything boots, updates, etc.

However it is giving me headaches with Windows. I was able to install Vista, then upgrade to Windows 7 ultimate, but Windows 10 refuses to install. No matter what type, x86 or x64. This is very odd behavior considering the success with Linux.

I have also used several different system information utilities to see what the features of the board are and there are mixed results. Some say it is capable of UEFI, some do not. It is a mixed bag.

Since there is no support on the Intel site except for the very hard to find manuals and outdated (vague) tutorials, I was referred to this forum for support by Customer Support over the phone.

I really need the BIOS and firmware updates but there’s nothing on the Intel website, not even archived. Now, I did get the CD-rom with the board, this was an unopened board in the original packaging. It even came with a poster. Intel does not carry the BIOS or firmware on the site anymore. Does anyone have archives of this?

I am also having difficulty figuring out how to solve a CPU error code

In BIOS, it tells me that it does not support CPU stepping, which I assume can be fixed with a BIOS upgrade.

It also tells me it is unable to apply the intel microcode.

I can boot the CD rom, however when it attempts to update firmware etc. through that GUI, it just hangs endlessly while checking for updates, probably due to the files being unavailable online. I am connected to the internet by CAT6, hard wired. It connects to the internet just fine in every OS I have installed.

Here are my System specs (well the relevant bits anyway)

it is a S500PSLSASR board

BIOS Version S5000.86B.10.00.0085

BIOS Date 11/29/2007 (last revision was probably sometime before 2010)

CPUs 2x Intel XEON X5450 @ 3.0 GHz

FSB is 1.33 MHz (?)

32 GB RAM (8 ECC FBDIMMs specifically for this system)

BMC firmware is rev. 0.64

HSC firmware is rev. 2.02

SDR rev. is FDAE9601DD3711DD

Board part# is E11025-103

I have an Nvidia Geforce 210 installed and running great. Not worried about graphics because it is a server board, that was a spare card and it simply helps me test things out without needing a web interface.

Power supply is 750w but I suspect that it probably would run better with something like a 1000w or higher power supply. Intel recommended nothing lower than 600w

error codes in BIOS are listed as 

84FF system log is full (I can clear this but it will just fill back up with the same errors)

8180 does not support CPU stepping frequency

8160 unable to apply microcode

8161 unable to apply microcode

Customer Support tech did not indicate that this was a server/processor mismatch and said a BIOS/firmware upgrade would most likely fix these errors.

Also when it boots, the POST codes are three beeps, then a pause and a single beep, probably related to the BIOS error codes. I’ve tried to hunt down the meaning of them and nothing relevant comes up in Google, everything suggests an error that would mean it fails to POST. But since I can boot into an OS obviously that’s not the case.

Are there any settings in BIOS I should be aware of to help fix any issues with the CPUs or anything else? I am nowhere near being able to set up RAID on it because

1) I need SAS drives

2) I also need proper cables for SAS drives and connectors for the onboard SAS ports (four total)

3) I probably want to get a RAID expansion card eventually.

I have several drives in the case but most are not connected. I have disconnected the 2 drives with linux, which are PATA. I have one Seagate drive connected to a SATA port and a DVD drive connected to the other SATA port. I have attempted to try a bootable flash drive on this system, and that never works no matter what I do. I have tried just about every bootable flash drive creation tool possible. There is also a USB key slot inside the case on the board but I have no idea if that will help me.

I know this is a lot of questions but any insight is appreciated. And no I don’t really want to try another board. I have this one, it works, I just want to optimize it.

Thanks

← Вернуться в раздел «Драйверы и прошивки BIOS»

Страницы: 1

Предыдущая тема: прошивки для transcend t.sonic 620

Форум Ru-Board.club — поднят 15-09-2016 числа. Цель — сохранить наследие старого Ru-Board, истории становления российского интернета. Сделано для людей.