Перфузор bbraun ошибка 1111

1.0

2

Unit Diagnosis / Calibration

Error Code

1

1100

Timebase too fast

2

1101

Timebase too slow

3

1102

Timebase fail

4

1103

Keyboard High

5

1104

EA_KEY defect 25sec

6

1105

No keydecode

7

1106

ROM Romtest defect Software

8

1107

ROM Program defect

9

1108

CM State without set

K_V_KM_ON

10

1109

MPU_Test failed

11

1110

RAM_Test failed

12

1111

active reset

13

1112 … 1114

Internal Error

14

1115

Drive too fast

15

1116

Drive too slow

16

1117 … 1118

Internal Error

17

1119

lcd backlight on defect

18

1120

lcd backlight off defect

19

1121

red led on defect

20

1122

red led off defect

21

1123

key pressed too long (without EA-

Key) 60sec

22

1124 … 1127

Internal Error

23

1128

Drive motion rightless forward

24

1129

Drive motion rightless backward

25

1130 … 1200

Internal Error

Table 2 — 3 Device alarms of the control microprocessor (Part 1 of 2)

2 — 6

Definition

Quartz of the processor PCB

Quartz of the processor PCB

Quartz of the processor PCB

Keyboard defective

Keyboard defective

Keyboard defective

Software

Software

Software

Software

Voltage supply during operation

interrupted

Motor drive

Recognition of direction of

rotation

Motor drive

Recognition of direction of

rotation

LC display defective

LC display defective

LC display defective

LC display defective

Keyboard defective

Motor drive

Recognition of direction of

rotation

Motor drive

Recognition of direction of

rotation

Possible Cause

Exchange processor PCB

Exchange processor PCB

Exchange processor PCB

Carry out device check

Carry out device check

Carry out device check

Update unit software

Update unit software

Update unit software

Update unit software

Exchange processor PCB

Exchange processor PCB

Exchange operating unit

Exchange operating unit

Exchange operating unit

Exchange operating unit

Carry out device check

Exchange processor PCB

Exchange processor PCB

Fault Clearance

Perfusor® Space, 1.0 gb

Service Manual

Perfusor® Space

1.21.0

Version 1.2 English

0

1.2

This Service Manual is valid for: Designation Part No.

Infusion syringe pump Perfusor® Space . . . . . . . . . . . . 0871 3030

This Service Manual is available under the following part number:

Designation Part No.

Service Manual Perfusor® Space, English . . . . . . . . . . . 8713 9020

Languages of this Manual The Service Manual for this unit can be supplied in the followinglanguages:

Designation Part No.

Service Manual Perfusor® Space, German . . . . . . . . . . 8713 9010

Service Manual Perfusor® Space, English (us) . . . . . . 8713 9020U

Service Manual Perfusor® Space, French . . . . . . . . . . . 8713 9030

0 — 2 Perfusor® Space, 1.2 gb

0

1.01.0

0 -Table of Contents

Important Preliminary Remarks Service Work Page 0 — 5

Technical Safety Checks Page 0 — 5Current Versions Page 0 — 5Revision Service Page 0 — 5Responsibility of the Manufacturer Page 0 — 6Quality Management Page 0 — 6Checks and Repair Page 0 — 6Notes on ESD Page 0 — 6Spare Parts and Test Equipment Page 0 — 7Setting Off Page 0 — 7List of Abbreviations Page 0 — 9

Contact Persons Technical Training Page 0 — 11Entry for Technical Training Page 0 — 11Ordering of Spare Parts and Test Equipment Page 0 — 11Service Hotline Page 0 — 11Return of Spare Parts and Test Equipment Page 0 — 11Safety Officer(§ 30 MPG) Page 0 — 11Translation Page 0 — 11

System Overview Description Page 1 — 1System Overview Page 1 — 1Physical Construction Page 1 — 2Function Page 1 — 3Unit Software Page 1 — 6Service Program Page 1 — 7Technical Data Page 1 — 12Options Page 1 — 12Accessories Page 1 — 12

Unit Diagnosis / Calibration General Page 2 — 1Alarms and Error Codes Page 2 — 3The Most Important Error Modes Page 2 — 8Device Check Page 2 — 9Calibration Page 2 — 14Procedural Instructions for Calibration Page 2 — 14Trouble Shooting Page 2 — 29

Disassembly / Assembly General Page 3 — 1Battery Module Page 3 — 9Unit Foot Page 3 — 11Operating Unit Page 3 — 12Upper Part of Housing Page 3 — 17Release Button Page 3 — 19Loudspeaker Page 3 — 19Drive Page 3 — 20Syringe Holder with Piston Brake Page 3 — 27Processor PCB Page 3 — 34Assembly / Installation Page 3 — 35Checks after Repair Page 3 — 47

Perfusor® Space, 1.0 gb 0 — 3

Table of Contents 0

1.01.0

Servicing the Unit Cleaning Page 4 — 1Servicing the Battery Page 4 — 1

Technical Safety Check (TSC) Perfusor® Space Page 5 — 1

Technical Safety Check (TSC) Power Supply SP Page 6 — 1

Procedural Instructions on the TSC Visual Inspection Page 7 — 1Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751 Page 7 — 2Functional Inspection Perfusor® Space Page 7 — 3Functional Inspection Power Supply SP Page 7 — 5

Test Equipment and Special Tools Test Equipment Page 8 — 1Special Tools Page 8 — 3

Spare Parts List Page 9 — 1

Revision Documentation Description of Version Page 10 — 1Version List of the Individual Pages Page 10 — 1

Index Page 11 — 1

0 — 4 Perfusor® Space, 1.0 gb

0

1.21.0

0 -Important Preliminary Remarks

Service Work The present manual is for your information only. The possession of

this manual does not authorize the performance of service work.Service tasks may only be executed by persons, who

— have received appropriate training on the system fromB. Braun

— are included in the revision service

— possess the necessary test equipment and mechanical aids,and

— fulfill the personal requirements (training and knowledge).

Technical Safety Checks The user is obliged to perform or to have performed the TechnicalSafety Checks on those medial products for which these checkshave been prescribed by the manufacturer and to carry them outaccording to the indications of the manufacturer as well as thegenerally approved technical standards while adhering to theperiods stated (§ 6 MP BetreibV).

B. Braun also recommends training on the Technical SafetyChecks, or to perform at least the steps indicated in the currentversion of the manual, as:

— the TSC requires that the instructions in the manuals areobserved

— the manuals are a reference for measurements

— depending on the unit type, the Service Program must becalled which may lead to a dangerous unit condition in caseof inappropriate operation. Furthermore, a special serviceconnector may be necessary.

Current Versions This manual version corresponds to the state when the manualwas written. B Braun reserves the right to make technicalmodifications. The state of the revision is indicated by the indexnumber in the footer of every page.

Revision Service The possession of this manual does not automatically meaninclusion in the revision service. You will be included in therevision service after:

— technical training by B. Braun Melsungen or

— a written order placed with the sales department of B. Braun(fee required).

Perfusor® Space, 1.2 gb 0 — 5

Important Preliminary Remarks 0

1.21.0

Responsibility of the Manufacturer The manufacturer, person who assembles, installs or imports thedevice can only be held responsible for safety, reliability andperformance if

— mounting, enhancements, new settings, changes or repairsare carried out by duly authorized persons,

— the electrical installation in the corresponding room meetsthe requirements of the VDE 0107, VDE 0100 part 710 orIEC 60364-7-710 and the national standards,

— the device is used in accordance with the instructions for useand the Service Manual,

— the Technical Safety Checks are performed at regularintervals,

— a current manual which corresponds to the revision state isused when carrying out maintenance, repair and service,

— the service technician takes part in the revision service,

— the technician has participated in a technical training coursefor the specific B. Braun unit.

Quality Management B. Braun is certified in accordance with DIN EN ISO 9001 andISO 13485. This certification also includes maintenance andservice.

The unit has the CE label. The CE label confirms that the devicecorresponds to the “Directive of the Council for Medical Products93/42/EC” of June 14, 1993.

Checks and Repair Training may only be performed by B. Braun. The possession of themanual does not authorize the performance of repairs. Theinstructions on electrostatic sensitive components (ESDstandards) must be observed.

After repair a device check or diagnosis is to be carried out.

Notes on ESD Semiconductors can be destroyed by electrostatic discharge.Especially MOS components can be damaged by interference fromelectrostatic fields, even without discharge via contact. This typeof damage is not immediately recognizable. Unit malfunctionscan even occur after a longer period of operation.

0 — 6 Perfusor® Space, 1.2 gb

Important Preliminary Remarks 0

1.2

Each workstation must be equipped according to therecommendations with the necessary static protective measures,if ESD components or boards are handled.

Each workstation must be equipped with a conductive tablesurface. The conductive surface, the soldering iron or thesoldering stations must be grounded via protective resistors.

Chairs must be of antistatic design. The floor or floor mats shouldbe of electrically conductive material.

Personnel must wear conductive wristbands which are connectedto a central ground potential via protective resistors, e.g. theground contact of a wall outlet. Furthermore it is recommendedthat personnel wear cotton clothing and electrically conductiveshoes to prevent electrostatic charge.

Spare Parts and Test Equipment Only use original spare parts from the manufacturer. Do nottamper with assembly groups which can only be exchangedcompletely. The spare parts required are listed in Section 9.

Service personnel are responsible for the calibration of their testequipment. Original test equipment can be calibrated at theworks of B. Braun. Further information is available upon request.

Setting Off Additional notes and warnings are set off as follows:

Note

Is used for additional or special notes concerning information andworking steps.

CAUTION

Is used for working steps which may result in damage to the unit,system or to a connected device.

WARNING

IS USED FOR WORKING STEPS WHICH MAY RESULT IN PERSONALINJURY.

References to chapters are shown as follows(see “Setting Off“ ➨ pg. 0 —

References to figures and tables are shown as followsFig.: 2 — 3 or Table 2 — 1

Fig.: 0 — 1

Perfusor® Space, 1.2 gb 0 — 7

Important Preliminary Remarks 0

1.21.0

References to item numbers in figures are shown as follows(Fig.: 1 — 1 / Item 1)In this case “Fig.: 1 – 1“ is the figure number and “Item 1“ the itemnumber within the figure.

When the Service Manual is stored as pdf-file, these referencesare displayed green. Click with the mouse button on a referenceto jump to the corresponding source.

Menu commands are described as:Menu File.

0 — 8 Perfusor® Space, 1.2 gb

Important Preliminary Remarks 0

1.2

List of Abbreviations Abbreviations which are not generally known, but are used in thismanual, are listed below.

CAN Controller Area Network

CE Communauté Européenne

CS Calibration Step

DIN German Industrial Norm

EN European Norm

ESD Electrostatic Discharge

FuP Function Microprocessor

IEC International ElectrotechnicalCommission

ISO International Organization forStandardization

ISP Infusomat® Space

ISPS Infusomat® Space (Silicon)

ISPP Infusomat® Space, (PVC)

CS Calibration Step

KuP Monitoring Microprocessor

LCD Liquid Crystal Display

MOS Shortname of the following company:MOS Technology, Inc.(Commodore Semiconductor Group)

PCA Patient Controlled Analgesia

PSP Perfusor® Space

SP Space (System)

SPC SpaceCover

SPCC SpaceCover comfort

SPCS SpaceCover standard

SPCO SpaceCom

SPCT SpaceControl

SPS SpaceStation

TEMP Temperature

TS Trouble Shooting Step

TSC Technical Safety Check

UTS Unit Test Step

Perfusor® Space, 1.2 gb 0 — 9

Important Preliminary Remarks 0

1.2

VDE Verband der Elektrotechnik, Elektronik und Informationstechnik e.V.(german association of engineers)

0 — 10 Perfusor® Space, 1.2 gb

0

1.2

0 -Contact Persons

Technical Training Via local representative.

Entry for Technical Training Application for a technical training course must be made via theresponsible representative.

Ordering of Spare Parts and Test Equipment Please contact your local B. Braun subsidary.

International Technicians (Intercompany)Nadja Machal

Fax: +49 5661 / 75 -47 89e-mail: [email protected]

Service Hotline Karl Tippel, Tanja KördelPhone: +49 5661 / 71 — 35 25Fax: +49 5661 / 71 — 35 26e-mail: [email protected]: [email protected]

Return of Spare Parts and Test Equipment B. Braun Melsungen AGSchwarzenberger Weg 73-79Wareneingang Werk C34 212 Melsungen Germany

Safety Officer(§ 30 MPG)

Dr. Ludwig Schütze-mail: [email protected]

Translation Brückner GmbH, Germany

Perfusor® Space, 1.2 gb 0 — 11

Contact Persons 0

1.2

For your notes:

0 — 12 Perfusor® Space, 1.2 gb

11.2

1 -System Overview

Description The Perfusor® Space (PSP) is according to IEC/EN 60601 resp. IEC/

EN 60601-2-24 a transportable infusion syringe pump foradministrating fluids in the nutritional therapy and infusiontechnique as well as for home care applications.

The medical specialist must decide on suitability for applicationon the basis of the warranted properties and the technical data.

System Overview The Space system is a modular design of modern infusiontechnology for stationary, mobile or private use. The key modulesand their connection to the peripheral devices are shown inFig.: 1 — 1.

All the pump types, Perfusor® Space, Infusomat® Space andInfusomat® Space P, as well as the other devices of the system areof modular design. Up to three pumps can be connected togethermechanically using L rails on the bottom of the unit and grooveson the top. They can then be fastened to a drip stand orappropriate rail using the pole clamp.

The SpaceControl module can be used to extend operation. Onesingle pump can be inserted onto this module. The pump is thenconnected via connectors to the module.

The SpaceStation module allows the set-up of a complete pumpsystem with up to 24 pumps. Up to four pumps can be installed inevery SpaceStation. The pumps are supplied with power via theintegrated power supply and the built-in connectors. The pumpsare connected to the optional SpaceCom via these connectors.SpaceControl can also be integrated into the system.

Up to six SpaceStations can be set-up as a column with a total of24 pumps. SpaceStation placed next to each other can beconnected via special connection cables, if the maximum numberof 24 pumps in maximum three columns is not exceeded.

SpaceCover Standard or SpaceCover Comfort forms the top ofeach column. Alarms are signalled by a row of LEDs and aloudspeaker in the SpaceCover Comfort.

Fig.: 1 — 1 Space system

Legend of fig. 1 — 1:ItemDesignation

1 SpaceCover

2 Infusion pump Infusomat® Space

3 Infusion syringe pump Perfusor® Space

4 SpaceControl

5 SpaceStation

1

2

3

4

5

Perfusor® Space, 1.2 gb 1 — 1

System Overview 1

1.0

Physical Construction

Fig.: 1 — 2 Perfusor® Space

Legend of fig. 1 — 2:ItemDesignation

1 Perfusor® Space

2 Drive head

3 Syringe holder with piston brake

4 Operating unit

5 Syringe area

6 Connector “P2“ for SpaceStation module, external 12 V DCand accessories

7 Connector “P3“, connection to SpaceControl module

8 Battery compartment cover

1

4

2

3

6

78

5

1 — 2 Perfusor® Space, 1.0 gb

System Overview 1

1.0

The Perfusor® Space housing mainly consists of the bottom partand the upper part.

The battery module is inserted in the rear of the housing upperpart. The opening is covered by the battery compartment cover.

The operating unit is attached to the front of the bottom part withtwo hinges. This operating unit covers the area for the syringes.The complete drive assembly, consisting of lead screw and drivehead with driving tube is located directly behind the syringe areain the bottom part of the housing. The housing bushing for thedriving tube is located in the side of the housing.

The syringe holder is mounted in the right side of the housingbottom part.

The processor PCB with the external connectors “P2” and “P3” islocated at the bottom of the housing bottom part.

Function There are two power options for the Perfusor® Space:

— via the inserted battery module

— via an external 12 V DC power supply (e.g. SpaceStation, SpaceControl, an external power supply or from an ambulance car) connected to connector “P2”

The voltage supplied is converted to the internal voltages requiredthrough a voltage transforming and monitoring circuit on theprocessor PCB.

An independent circuit in the battery module monitors the batterycells and controls their charge condition.

The Perfusor® Space is connected to a SpaceControl by connector“P3”.

The function processor controls all the functions of the Perfusor®Space. Data is stored in a non-volatile memory which alsocontrols the external data transfer.

The control microprocessor monitors all important responses ofthe function processor to incoming information. If a responsedoes not correspond with that expected by the controlmicroprocessor, an error message is generated and the device isswitched to a safe stop state.

The drive motor is monitored by a detector for speed and directionof rotation. The extended end position of the drive head isdetected by a switch on the processor PCB.

The pressure in the infusion system is measured through a straingauge measuring in the drive head and monitored in the device

Perfusor® Space, 1.0 gb 1 — 3

System Overview 1

1.0

electronics. The data from the strain gauge is continuouslycompared with the limit values which are calculated dependenton the selected syringe type and the pressure settings. When thelimit values are exceeded an alarm is automatically triggered andthe pressure in the infusion system is reduced. In addition themaximum possible pressure is limited via a second independentsystem which monitors motor current.

The syringe holder is connected to a potentiometer. The syringesize is determined from the resistance of the potentiometer.

The syringe is fixed with the syringe holder and the axial fasteningdevice. The syringe piston is fastened with two claws in the drivehead. When a syringe is inserted the syringe piston is held by thepiston brake, until the piston has been caught by the claws.

Keyboard and display as well as the syringe area are illuminated.

1 — 4 Perfusor® Space, 1.0 gb

System Overview 1

1.0

Fig.: 1 — 3 Block diagram Perfusor® Space

Perfusor® Space, 1.0 gb 1 — 5

System Overview 1

1.2

Unit Software Approved Software Versions

688A030032

— Basic software

688A030035

— Improved functions

688A030040

— Improved functions

— Languages French and Swedish added

688B030002

— Improved functions

688B030003

— CAN bus functioning

688C030001

— Dose calculation

— Changed CAN log

688D030001

— — Drug list data base

— — Changed user language

688E030002

— — Improved functions

— — Piggyback

— — Soft limits

Software Update of the Unit

The instructions for updating the software are supplied with thesoftware itself.

CAUTION

If the device is disconnected while the software is being updatedor the device or PC is switched off, a component of the softwaremay be seriously damaged so that repairs are no longer possible.In such a case the software cannot be updated via the PC and thedevice must be returned to B. Braun.

Fig.: 1 — 4

Position 1 2 3 4 5 6 7 8 9 10

Digit 6 8 8 C 0 3 0 0 0 1

Revision level

Hardware

Software group

Device type: Perfusor® Space

1 — 6 Perfusor® Space, 1.2 gb

System Overview 1

1.2

Service Program Approved Version

Note

Please note that text and / or functions of the Service Programmay change depending on the software version. The followingscreen illustrations are only examples and represent the statewhen the manual was printed.

— 0.0.28

— 1.0.0

— 1.1.2

— 1.1.3

— 1.1.4

— 1.2.1

— 1.3.5

— 1.5.0

— 2.0.1

— 3.1.0

Perfusor® Space, 1.2 gb 1 — 7

System Overview 1

1.2

Starting the Service Program

Note

Installation and further operation of the Service Program isdescribed in its separate instructions for use.

1. Start the „HiBaSeD.exe“ program (History, Barcode, Service, Drug list) on the PC. The Service Program is loaded and started and the initial window of the Service Program is displayed.

2. Read the notes carefully.

3. Mark the field “I accept all conditions” and then the field “Yes” to confirm that you have read the notes.

Note

Click the field “English” to switch the language of the notes overto English.

4. Enter the password and confirm it by clicking the field “Start”.

The Service Program checks the PC interfaces for connected devices of the Space system. Units that were found are displayed for a short moment on the screen.

Fig.: 1 — 5

Fig.: 1 — 6

Fig.: 1 — 7

1 — 8 Perfusor® Space, 1.2 gb

System Overview 1

1.2

The work window of the Service Program appears on the screen. All devices recognized are listed in the left column.

5. Activate the desired device from the list on the left in the work window with a double-click. The device data is then displayed below the device name.

Fig.: 1 — 8

Perfusor® Space, 1.2 gb 1 — 9

System Overview 1

1.2

If the unit software version is not compatible with the Service Program version, a window opens prompting the operator to change the Service Program version. This window displays a compatibility list of the Service Program- and unit software versions.

If Service Program- and unit software versions are compatible, all the Service Program functions are activated.

Fig.: 1 — 9

Fig.: 1 — 10

1 — 10 Perfusor® Space, 1.2 gb

System Overview 1

1.2

Service Program Version

1. Open the “HiBaSeD“ window via Help ➨ Info …. The current version of the Service Program is shown in this window.

2. Close the window by clicking “OK”.

Compatibility List

1. Open the “Unit — Compatibility“ window via Help ➨ Compatibility. This window displays the compatibility of the HiBaSeD-version and the unit software version.

2. Close the window by clicking “OK”.

Quit the Service Program

1. Exit the Service Program via File ➨ Exit.

2. Disconnect a power supply which might be connected from the unit.

3. Switch off the unit.

4. Remove the battery module.

5. The device can be restarted after appr. 10 seconds.

Fig.: 1 — 11

Fig.: 1 — 12

Perfusor® Space, 1.2 gb 1 — 11

System Overview 1

1.2

Technical Data All technical data is indicated in the instructions for use.

Options The functions of the individual options are detailed in theinstructions for use.

Perfusor® SpaceDesignation Part No.:

Power supply Euro . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3110A

Power supply UK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3111A

Power supply USA / Japan . . . . . . . . . . . . . . . . . . . . . . 0871 3112A

Power supply Australia. . . . . . . . . . . . . . . . . . . . . . . . . 0871 3113A

Power supply South Africa. . . . . . . . . . . . . . . . . . . . . . 0871 3115A

Accessories Designation Part No.:

Charger SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3170battery charging station

Connection cable staff call SP. . . . . . . . . . . . . . . . . . . . 0871 3232

Power supply cable 12 V . . . . . . . . . . . . . . . . . . . . . . . . 0871 3231for ambulance cars

CombiLead SP 12 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3133connection cable, pump — pump

InterfaceLead SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3234interface cable RS232

InterfaceLead SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3230interface cable CAN SP

SpaceClamp SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3130The SpaceClamp is a holder attached on beds for oneor several Space system pumps.

Short stand SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3135

1 — 12 Perfusor® Space, 1.2 gb

21.1

2 -Unit Diagnosis / Calibration

General

WARNING

WHILE TESTING THE UNIT AND TROUBLE SHOOTING THEOPERATOR/SERVICE TECHNICIAN MUST WORK WITH VOLTAGESUP TO 115 / 230 V AC. THESE VOLTAGES MAY CAUSE INJURIESWHICH ARE DANGEROUS TO LIFE AND LIMB. THE NATIONAL ANDINTERNATIONAL SAFETY REGULATIONS ARE TO BE ADHERED TO.

Before each disassembly and assembly of a unit subsystem checkthe connectors, plug contacts and connections for corrosion andtight fit. These fault types are not described again in the followingtrouble shooting list.

The following equipment and gauges are necessary for testing theunit and/or performing troubleshooting:

— PC

— Service connector SP

— Service Program HiBaSeD

— Interface cable

— Syringe 2 ml / 3 ml

— Syringe 10 ml

— Syringe 30 ml

— Diameter gauge 32.0 mm

— Diameter gauge 23.4 mm

— Diameter gauge 15.7 mm

— Diameter gauge 9.0 mm

— Length gauge PSP

— Syringe gauge “#Lehre OPS 50“with push-button plate and motor power test adapter for Perfusor® Space

There are pictures of the gauges in Chapter „Special Tools“ (➨S. 8 — 3).

CAUTION

Take special care when carrying out measurements on an openand switched-on unit. Short circuits and wrong measuringmethods can cause serious damage to or destroy the subsystemsof the device.

Perfusor® Space, 1.1 gb 2 — 1

Unit Diagnosis / Calibration 2

1.0

The unit check, calibration and trouble shooting are subdividedinto numbered working steps (Unit Test Step UTS, Calibration StepCS, Trouble Shooting TS) and are based on each other.

Beginning with UTS 1 the operation described here has to beexecuted. The consequences of the steps performed are listed inthe “Function“ column. If the result corresponds to theconsequence, the working step must be carried out to whichreference is made in the column “If yes”. If the result does notcorrespond with the function described, the working step incolumn “If no” is to be executed.

One example is given in Fig.: 2 — 1.

Steps for which additional information is required are describedafter the table in detail.

Fig.: 2 — 1 Model tables

UTS Activity Function If yes If no1 UTS 2

2 UTS 3 TS 1

3 UTS 4

4 UTS 5 TS 4

5

Model table 1

TS Activity Function1 UTS 3 TS 2

2 TS 3 TS 4

3 UTS 3

4 UTS 4 TS 4

5 UTS 4

Model table 2

2 — 2 Perfusor® Space, 1.0 gb

Unit Diagnosis / Calibration 2

1.0

Alarms and Error Codes The alarms of the Perfusor® Space are classified in 5 categories.These categories are listed hereafter according to theirimportance.

— Alarm adviceIn case of unacceptable inputs corresponding messages are displayed (e.g. “Caution! Rate out of range“, “The parameter cannot be changed“) and a beep sounds.

— Pre-alarmPre-alarms are triggered several minutes (depending on the service settings) before the operating alarms.

— Reminder alarmA reminder alarm is triggered if the device is not operated for two minutes when input or operation was not finished.

— Operating alarmIn case of an operating alarm the infusion is stopped. An audible signal is released, the red LED flashes and a staff call is triggered. The message “Alarm“ and the cause of the alarm appear on the display.

— Device alarm

The most important alarms and error codes as well as theirmeaning and possible fault clearance are specified in thefollowing lists.

Note

The device should be checked after every repair or service (pleasesee „Device Check“ ➨ pg. 2 — 9).

Perfusor® Space, 1.0 gb 2 — 3

Unit Diagnosis / Calibration 2

1.0

Alarms

Alarm Possible Cause Fault Clearance1 Battery nearly discharged (type: pre-

alarm)The device was not connected to the mains long enough

Operate the device with battery until the message “Battery discharged“ is displayed and the unit is switched off. Then connect the unit to the mains for at least 6 hours.

Battery module defective or too old Replace battery module

2 Battery discharged (type: operating alarm)

The device was not connected to the mains long enough

Connect the unit to the mains for at least 6 hours

Battery module defective Replace battery module

3 Battery cover open (type: operating alarm)

❒ The battery compartment cover is not correctly closed

Insert the battery compartment cover correctly

❒ The magnet in the battery compartment cover is missing

Exchange the battery compartment cover

❒ The battery compartment cover is not recognized by the battery module

Replace battery module

4 Drive blocked (type: operating alarm) ❒ The drive was manually blocked Eliminate blockage

❒ Driving force too low Connect the unit to the mains for at least 6 hours and charge battery

Re-calibrate the device

❒ The drive is physically damaged Replace drive

5 Malfunction of claws (type: operating alarm)

❒ The syringe piston was not recognized

Select or insert correct syringe type

Loosen the syringe via the emergency release button in the drive head and insert again

Re-calibrate the device

❒ The claws or the claw drive are/is damaged

Replace drive head

6 Push-button has no contact (type: operating alarm)

❒ Negative pressure in the syringe system

See instructions for use

❒ Syringe was removed without opening the syringe holder

See instructions for use

❒ Push-button sensor defective Replace drive head

7 Device alarm (type: device alarm) A serious internal fault was detected in the system

Switch device off and on

Carry out a device check (please see „Device Check“ ➨ pg. 2 — 9)

Table 2 — 1 Alarms

2 — 4 Perfusor® Space, 1.0 gb

Unit Diagnosis / Calibration 2

1.0

Device Alarms of the Function Processor

Error Code Definition Possible Cause Fault Clearance1 1001 … 1013 Internal Error

2 1014 Loudspeaker not off Loudspeaker connector Check the loudspeaker connector

Loudspeaker Check the loudspeaker

3 1015 Loudspeaker lost Loudspeaker connector Check the loudspeaker connector

Loudspeaker Check the loudspeaker

4 1016 Loudspeaker shorted Loudspeaker connector Check the loudspeaker connector

Loudspeaker Check the loudspeaker

5 1017 KuP switchoff path defect (K_SM_CLK)

Switch off path

6 1018 ADC pressure out of range Pressure measurement in drive head

Carry out calibration

7 1019 Internal Error

8 1020 FUP Flash Memory Error Software Update unit software

9 1021 FUP different version KuP to FuP Software Update unit software

10 1022 FUP pressure zero test fail Pressure measurement in drive head

Carry out calibration

11 1023 FUP pressure offset test fail Pressure measurement in drive head

Carry out calibration

12 1024 FUP EA key closed to long 20sec Keyboard defective Carry out device check

13 1025 Internal Error

Table 2 — 2 Device alarms of the function processor

Perfusor® Space, 1.0 gb 2 — 5

Unit Diagnosis / Calibration 2

1.2

Device Alarms of the Control Microprocessor

Error Code Definition Possible Cause Fault Clearance1 1100 Timebase too fast Quartz of the processor PCB Exchange processor PCB

2 1101 Timebase too slow Quartz of the processor PCB Exchange processor PCB

3 1102 Timebase fail Quartz of the processor PCB Exchange processor PCB

4 1103 Keyboard High Keyboard defective Carry out device check

5 1104 EA_KEY defect 25sec Keyboard defective Carry out device check

6 1105 No keydecode Keyboard defective Carry out device check

7 1106 ROM Romtest defect Software Update unit software

8 1107 ROM Program defect Software Update unit software

9 1108 CM State without set K_V_KM_ON

10 1109 MPU_Test failed Software Update unit software

11 1110 RAM_Test failed Software Update unit software

12 1111 active reset Voltage supply during operation interrupted

13 1112 … 1114 Internal Error

14 1115 Drive too fast Motor driveRecognition of direction of rotation

Exchange processor PCB

15 1116 Drive too slow Motor driveRecognition of direction of rotation

Exchange processor PCB

16 1117 … 1118 Internal Error

17 1119 lcd backlight on defect LC display defective Exchange operating unit

18 1120 lcd backlight off defect LC display defective Exchange operating unit

19 1121 red led on defect LC display defective Exchange operating unit

20 1122 red led off defect LC display defective Exchange operating unit

21 1123 key pressed too long (without EA-Key) 60sec

Keyboard defective Carry out device check

22 1124 … 1127 Internal Error

23 1128 Drive motion rightless forward Motor driveRecognition of direction of rotation

Exchange processor PCB

24 1129 Drive motion rightless backward Motor driveRecognition of direction of rotation

Exchange processor PCB

25 1130 … 1200 Internal Error

26 1201 different version FuP to KuP Software Update unit software

Table 2 — 3 Device alarms of the control microprocessor (Part 1 of 2)

2 — 6 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.0

27 1202 E_ERROR_STEPMOTOR_1 Phase not ok

Drive motor, lead screw Exchange processor PCB

28 1203 E_ERROR_STEPMOTOR_2 Current value not 0x55

Motor driveRecognition of direction of rotation

Carry out calibration

29 1204 E_ERROR_STEPMOTOR_3 K_SM_CLK defect

Motor driveRecognition of direction of rotation

Carry out calibration

30 1205 E_ERROR_STEPMOTOR_4 Phase not ok

Motor driveRecognition of direction of rotation

Carry out calibration

31 1206 E_ERROR_STEPMOTOR_5 Current value not 0

Motor driveRecognition of direction of rotation

Carry out calibration

32 1207 E_ERROR_STEPMOTOR_6 Current value not 0x55

Motor driveRecognition of direction of rotation

Carry out calibration

33 1208 E_ERROR_STEPMOTOR_7 Current value not 0xAA

Motor driveRecognition of direction of rotation

Carry out calibration

34 1209 E_ERROR_STEPMOTOR_8 Phases not 0

Motor driveRecognition of direction of rotation

Carry out calibration

35 1210 E_ERROR_DCMOTOR_1 Piston brake drive motor def.Claw drive in drive head defectivePiston brake light barrier def.

36 1211 E_ERROR_DCMOTOR_2

37 1212 E_ERROR_DCMOTOR_3

38 1213 E_ERROR_DCMOTOR_4

39 1214 E_ERROR_DCMOTOR_5

40 1215 no V_MOT Voltage transformer defective Exchange processor PCB

41 1216 overvoltage test fail

42 1217 no V_MOT

43 1218 undervoltage test fail

44 1220 syringeholder defect Syringe holder or potentiometer def.

Replace syringe holderExchange processor PCB45 1221 syringe change timeout

46 1237 … 1238 Internal Error

47 1239 plunger plate sensor defect Pressure measurement in drive head

Replace drive head

48 1240 … 1254 Internal Error

Error Code Definition Possible Cause Fault Clearance

Table 2 — 3 Device alarms of the control microprocessor (Part 2 of 2)

Perfusor® Space, 1.0 gb 2 — 7

Unit Diagnosis / Calibration 2

1.0

The Most Important Error Modes The following list specifies the most important error modes andtheir clearance.

Note

The device must be checked after every repair or service (pleasesee „Device Check“ ➨ pg. 2 — 9).

Error Possible Cause Fault Clearance1 The battery module discharges too fast The device was not used for a longer time.

The battery module was not discharged and charged at regular intervals.

❒ Discharge and charge battery module several times

❒ Replace battery module

Table 2 — 4

2 — 8 Perfusor® Space, 1.0 gb

Unit Diagnosis / Calibration 2

1.2

Device Check

UTS Activity Function If yes If no1 The device is inserted in a SpaceStation or

connected to a SpaceControl.UTS 2 UTS 3

2 Remove the device. UTS 4

3 Loosen all connections from the device. UTS 4

4 Remove syringe and close syringe holder. UTS 5

5 Plug service connector SP on connector “P2”. UTS 6

6 Connect power supply to the device via service connector SP.

All LEDs light up for a short moment. UTS 7 TS 1

7 The battery charge state and the mains connection are displayed at the top left of the LC display (without lighting).

UTS 8 TS 5

8 Switch on unit. All LEDs light up (from left: yellow, green, blue). UTS 9 TS 5

9 A short deep and then a short high beep sound. UTS 10 TS 7

10 The colour of the middle LED changes from green to red, then the LED goes out. The yellow and the blue LED remain on for a short moment.

UTS 11 TS 8

11 The message “Self-test active” and the current software version are displayed.

UTS 12 TS 8

12 Keyboard, LC display as well as the syringe area are illuminated.

UTS 13 TS 9

13 The drive head moves to the extended end position. UTS 14 TS 11

14 The claws in the syringe head close and open. UTS 15 TS 14

15 The message “Drive moves back / Syringe change” appears on the display.

UTS 16 TS 16

16 “Open syringe holder and insert syringe or press “C“ to input parameters“ is displayed.

UTS 17 TS 16

17 Open syringe holder. “Syringe change / Please insert syringe …” is displayed.

UTS 18 TS 17

18 Press the “>“ key. The following service information is displayed:- Brake: stopped by ____- drivetest ok- Size: 35.4 KuP 35.4 FuP

UTS 19 TS 19

19 Insert syringe 30 ml. The syringe piston is fastened with the syringe holder blade.

UTS 20 TS 21

20 “Brake: stopped by current“ is displayed. UTS 21 TS 21

21 Insert syringe 2 ml / 3 ml. “Brake: stopped by holder“ is displayed. UTS 22 TS 21

22 Open syringe holder and remove syringe. “Brake: stopped by light barrier“ is displayed. UTS 23 TS 21

Table 2 — 5 Device check (Part 1 of 5)

Perfusor® Space, 1.2 gb 2 — 9

Unit Diagnosis / Calibration 2

1.2

23 3.54 is shown for FuP on the LC display. The value displayed for FuP may have a maximum tolerance of ± 0.04.

UTS 24 CS 1

24 Close syringe holder. The value for FuP changes to 7.0 ± 0.4. UTS 25 CS 1

25 Insert diameter gauge 9.0 mm. The value for FuP changes to 9.0 ± 0.4. UTS 26 CS 1

26 Insert diameter gauge 15.7mm. The value for FuP changes to 15.7 ± 0.4. UTS 27 CS 1

27 Insert diameter gauge 23.4 mm. The value for FuP changes to 23.4 ± 0.4. UTS 28 CS 1

28 Insert diameter gauge 32.0 mm. The value for FuP changes to 32.0 ± 0.4. UTS 29 CS 1

29 The sum of the tolerances of UTS 23 to UTS 28 must not exceed 1.0.

UTS 30 CS 1

30 Insert syringe 2 ml / 3 ml. UTS 31

31 Press the “>“ key. The syringe selection is displayed. UTS 32

32 Select a syringe. The drive head moves to the syringe piston, the claws in the drive head close and the message “Syringe is caught / Please wait” is displayed.

UTS 33 TS 26

33 Test all buttons on the operating unit during a functional check (carry out infusion).

When the buttons are pressed the desired reaction is carried out.

UTS 34 TS 29

34 Open syringe holder while the infusion is administered.

The red LED on the operating unit flashes and the red LED of the service connector SP lights up. The message “Alarm / Syringe holder” is displayed.

UTS 35 TS 31

35 Close syringe holder and continue infusion. UTS 36

36 Stop infusion. UTS 37

37 Open syringe holder. “Syringe change / Initiate change? Yes / No” is displayed.

UTS 38

38 Confirm with “Yes”. The claws in the drive head open and the drive head moves to the extended end position.

UTS 39

39 Remove syringe. UTS 40

40 Insert syringe gauge for the strain gauge measurement, close syringe holder and select syringe type „#Lehre OPS50“.

WARNING

DURING THE STRAIN GAUGE MEASUREMENT WITHSYRINGE GAUGE THE SYRINGE HOLDER MUST NOTBE OPENED. THE SYRINGE GAUGE IS UNDER VERYHIGH PRESSURE AND MAY CAUSE INJURIES IF THEPRESSURE IS RELIEVED SUDDENLY.

UTS 41

UTS Activity Function If yes If no

Table 2 — 5 Device check (Part 2 of 5)

2 — 10 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.0

41 Input a delivery rate of 200 ml/h, select pressure stage 1 and start infusion.

When the maximum pressure of this pressure stage is reached, the delivery is stopped, the red LED on the operating unit flashes and the message “Alarm / Pressure too high” is displayed.The value read on the syringe gauge (in N) must match the value indicated for the strain gauge measurement of this pressure stage in the TSC.

UTS 42 CS 1

42 Confirm alarm. UTS 43

43 Select pressure stage 3 and start infusion. When the maximum pressure of this pressure stage is reached, the delivery is stopped, the red LED on the operating unit flashes and the message “Alarm / Pressure too high” is displayed.The value read on the syringe gauge (in N) must match the value indicated for the strain gauge measurement of this pressure stage in the TSC.

UTS 44 CS 1

44 Confirm alarm. UTS 45

45 Select pressure stage 8 and start infusion. When the maximum pressure of this pressure stage is reached, the delivery is stopped, the red LED on the operating unit flashes and the message “Alarm / Pressure too high” is displayed.The value read on the syringe gauge (in N) must match the value indicated for the strain gauge measurement of this pressure stage in the TSC.

UTS 46 CS 1

46 Confirm alarm and pull syringe holder briefly. UTS 47

47 Confirm syringe change, release syringe gauge and remove gauge.

WARNING

WHILE CHECKING THE MOTOR POWER LIMITATIONWITH THE SYRINGE GAUGE THE SYRINGE HOLDERMUST NOT BE OPENED. THE SYRINGE GAUGE ISUNDER VERY HIGH PRESSURE AND MAY CAUSEINJURIES IF THE PRESSURE IS RELIEVED SUDDENLY.

UTS 48

48 Insert the motor power test adapter in the drive head to check the motor power limitation.

UTS 49

49 Dismount the push-button plate from the syringe gauge and insert syringe gauge.

UTS 50

UTS Activity Function If yes If no

Table 2 — 5 Device check (Part 3 of 5)

Perfusor® Space, 1.0 gb 2 — 11

Unit Diagnosis / Calibration 2

1.0

50 Select syringe type “#Lehre OPS 50“. The threaded end of the syringe gauge must be introduced in the opening of the motor power test adapter. To do this, hold on to the syringe gauge, if necessary by hand, in the syringe area.

UTS 51

51 Select pressure stage 1 and start infusion. When the maximum pressure of this pressure stage is reached, the delivery is stopped, the red LED on the operating unit flashes and the message “Alarm / Drive blocked” is displayed.The value read on the syringe gauge (in N) must match the value indicated for the motor power limitation in the TSC.

UTS 52 CS 1

52 Confirm alarm. UTS 53

53 Select pressure stage 3 and start infusion. When the maximum pressure of this pressure stage is reached, the delivery is stopped, the red LED on the operating unit flashes and the message “Alarm / Drive blocked” is displayed.The value read on the syringe gauge (in N) must match the value indicated for the motor power limitation in the TSC.

UTS 54 CS 1

54 Confirm alarm. UTS 55

55 Select pressure stage 6 and start infusion. When the maximum pressure of this pressure stage is reached, the delivery is stopped, the red LED on the operating unit flashes and the message “Alarm / Drive blocked” is displayed.The value read on the syringe gauge (in N) must match the value indicated for the motor power limitation in the TSC.

UTS 56 CS 1

56 Confirm alarm and pull syringe holder briefly. UTS 57

57 Confirm syringe change, release syringe gauge and remove gauge.

WARNING

WHILE CHECKING THE MOTOR POWER LIMITATIONWITH THE SYRINGE GAUGE THE SYRINGE HOLDERMUST NOT BE OPENED. THE SYRINGE GAUGE ISUNDER VERY HIGH PRESSURE AND MAY CAUSEINJURIES IF THE PRESSURE IS RELIEVED SUDDENLY.

UTS 58

58 Insert syringe type 30 ml and lock PCA-lock with PCA-key.

The syringe holder cannot be opened. UTS 59 TS 32

UTS Activity Function If yes If no

Table 2 — 5 Device check (Part 4 of 5)

2 — 12 Perfusor® Space, 1.0 gb

Unit Diagnosis / Calibration 2

1.0

59 Open PCA-lock and remove syringe. UTS 60

60 Insert syringe type 10 ml and lock PCA-lock with PCA-key.

The syringe holder cannot be opened. UTS 61 TS 32

61 Open PCA-lock and remove syringe. UTS 62

62 Switch device off. The message “Pump is switched off in 3 .. 2 .. 1 sec” is displayed.

UTS 63

63 “Drive is parked …/ Please wait …“ is displayed. The drive head moves to the retracted park position.

UTS 64

64 The device switches off. UTS 65 TS 35

65 Pull off the power supply. The blue LED lights up for a short moment. UTS 66 TS 35

66 Switch on unit. UTS 67

67 Open the battery compartment cover when the drive head has moved to the extended end position.

An alarm signal sounds, the red LED flashes and “Alarm / Battery cover open / Confirm with “OK” is displayed.

UTS 68 TS 36

68 Remove battery. A permanent alarm is triggered. UTS 69 TS 38

69 Insert battery, close battery compartment cover and switch on the device.

The message “Devicealarm / 1111” is displayed. UTS 70

70 Switch the device off, remove service connector SP and dismount test structure.

This step terminates the device check.

UTS Activity Function If yes If no

Table 2 — 5 Device check (Part 5 of 5)

Perfusor® Space, 1.0 gb 2 — 13

Unit Diagnosis / Calibration 2

1.2

Calibration

Procedural Instructions for Calibration Starting Calibration

Note

Calibration must be carried out with power supply connected,since the calibration can be interrupted suddenly if the unit isbattery-operated and the battery gets discharged so that thedevice is switched off.

Note

Please note that text and / or functions of the Service Programmay change depending on the software version. The followingscreen illustrations are only examples and represent the statewhen the manual was printed.

1. Start the Service Program (please see „Starting the Service Program“ ➨ pg. 1 — 8).

2. Select the unit to be calibrated in the left column of the window with a double mouse-click. The blue and the yellow LED blinks in opposite with the red LED.

3. Select the register tab “Calibration”.

CS Activity Function If yes If no1 Connect unit to PC with interface cable. CS 2

2 Start Service Program on the PC (please see „Starting the Service Program“ ➨ pg. 1 — 8).

The desired device is found by the Service Program and then displayed.

CS 3

3 Start calibrating the unit (please see „Starting Calibration“ ➨ pg. 2 — 14).

CS 4

4 Carry out calibration of the claws (please see „Claw Calibration“ ➨ pg. 2 — 23).

Calibration of the claws was terminated successfully.

CS 5

5 Carry out calibration of the syringe holder (please see „Syringe Holder Calibration“ ➨ pg. 2 — 23).

Calibration of the syringe holder was terminated successfully.

CS 6

6 Carry out pressure calibration (please see „Pressure Calibration“ ➨ pg. 2 — 26).

Pressure calibration was terminated successfully. CS 7

7 Close the Service Program (please see „Quit the Service Program“ ➨ pg. 1 — 11).

UTS 23

Table 2 — 6 Calibration

2 — 14 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

4. Press the “New device“ button in the frame “Calibration procedure”. The window “Worker ID“ is opened.

Note

If you do not have an allocated worker id, enter “0001”.

Fig.: 2 — 2

Perfusor® Space, 1.2 gb 2 — 15

Unit Diagnosis / Calibration 2

1.2

5. Input your user number in the window “Worker ID” as well as the six-digit serial number of the device, if necessary.

6. Confirm the input with “OK“.

Note

If HiBaSeD could not clearly read the device serial number, thenumber must be entered according to the rating plate.

If the unit is not yet switched on, the window „Unit on/off“ opens and the user is asked to select the desired language.

7. Select the desired language. The respective operating steps are explained in detail in the instructions for use.After the language was confirmed the unit switches on and the window „Unit on/off“ closes.

Fig.: 2 — 3

Fig.: 2 — 4

Fig.: 2 — 5

2 — 16 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

Note

If calibration is interrupted data is written back to the device andmarked as invalid, if this is still possible. When the ServiceProgram is started again the data is marked as faulty andhighlighted red.

Fig.: 2 — 6

Perfusor® Space, 1.2 gb 2 — 17

Unit Diagnosis / Calibration 2

1.2

8. The frame “Data selection” is now activated.

If the “Adjustment …“ button was pressed in the “Calibration process” frame, the desired data for editing and transmission can now be selected in the “Data selection” frame.

Note

The device must not be switched off during calibration even if thismessage is displayed on the LC display (“Turn pump off”, “Switchdevice off”).

Fig.: 2 — 7

2 — 18 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

9. Mark at least the “Calibration data“ field in this frame if you have not selected “New device” and confirm by clicking “OK”. The device switches on and the drive head moves to the extended end position. You are prompted to press the blue connection key on the device.

10. Press the blue connection key on the device after the drive head has moved to the end position.

Fig.: 2 — 8

Perfusor® Space, 1.2 gb 2 — 19

Unit Diagnosis / Calibration 2

1.2

11. In the frame “Calibration mode“ you can choose between a complete or a partial calibration. Select the desired calibration mode with the mouse pointer.

Note

The following description is applicable to a complete and a partialcalibration. All possible calibrations are carried out one after theother if a complete calibration is selected. Interrupting thecalibration may trigger an alarm in the device.

Fig.: 2 — 9

2 — 20 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

12. Press the “OK“ button after you have selected the calibration elements. The necessary device data is read out and stored in the PC.

Fig.: 2 — 10

Fig.: 2 — 11

Fig.: 2 — 12

Fig.: 2 — 13

Perfusor® Space, 1.2 gb 2 — 21

Unit Diagnosis / Calibration 2

1.2

13. The frame “Element selection” is now activated.

If you have selected a complete calibration in the “Calibration mode” frame, the individual calibration elements are already selected and cannot be changed. Actuate the “OK“ button.

If you have chosen a partial calibration in the frame “Calibration mode”, you can click the calibration element “Claw”, “Syringe holder” and “Pressure” with the mouse pointer. A multiple choice is possible. Press the “OK“ button after you have selected the calibration elements.

Fig.: 2 — 14

2 — 22 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

Claw Calibration

1. The frame “Claw calibration“ is activated and calibration is started.

2. The claws in the drive head are closed and the query “Claw closed? Please confirm“ is displayed in the frame “Claw calibration“.

3. Check whether the claws are closed. Then actuate the “Yes” button.

4. The claws in the drive head are opened and the query “Claw open? Please confirm“ is displayed in the frame “Claw calibration“.

5. Check whether the claws are opened. Then actuate the “Yes” button.

Syringe Holder Calibration

1. The frame “Syringe holder calibration“ is activated and calibration is started.

2. Insert diameter gauge 32.0 mm and close the syringe holder.

Note

The diameter gauge must not be held by the axial fastening of thehousing side part. They must be inserted in such a way that thearea of the diameter gauges touches the axial fastening edge.

3. Press the “OK“ button.

Fig.: 2 — 15

Fig.: 2 — 16

Fig.: 2 — 17

Perfusor® Space, 1.2 gb 2 — 23

Unit Diagnosis / Calibration 2

1.2

4. Insert diameter gauge 23.4 mm and close the syringe holder.

5. Press the “OK“ button.

6. Insert diameter gauge 15.7 mm and close the syringe holder.

7. Press the “OK“ button.

Fig.: 2 — 18

Fig.: 2 — 19

2 — 24 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

8. Insert diameter gauge 9.0 mm and close the syringe holder.

9. Press the “OK“ button.

10. Open the syringe holder and remove the diameter gauge. Press the “OK“ button.

Note

The syringe holder must always be completely turned and theaxial fastening completely opened.

Fig.: 2 — 20

Fig.: 2 — 21

Perfusor® Space, 1.2 gb 2 — 25

Unit Diagnosis / Calibration 2

1.2

11. Close the syringe holder and actuate the “OK“ button.

If calibration was not terminated successfully, an error message is displayed on the PC screen.

Pressure Calibration

Note

The term “Power gauge” in the windows of the Service Programcorresponds to the syringe gauge.

1. The frame “Pressure calibration/length/PWM“ is activated and calibration is started.

2. Insert the length gauge and close the syringe holder.

3. Press the “OK“ button.

Fig.: 2 — 22

Fig.: 2 — 23

2 — 26 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.2

4. If “Insert power gauge and confirm with OK” is displayed in the frame “Pressure calibration/length/PWM”, open the syringe holder and remove the length gauge.

WARNING

DURING PRESSURE CALIBRATION WITH THE SYRINGE GAUGE THESYRINGE HOLDER MUST NOT BE OPENED. THE SYRINGE GAUGE ISUNDER VERY HIGH PRESSURE AND MAY CAUSE INJURIES IF THEPRESSURE IS RELIEVED SUDDENLY.

5. Insert the syringe gauge with the attached push-button plate (small diameter) for the Perfusor® Space and close the syringe holder.

6. Press the “OK“ button.

7. The power calibration is carried out. When calibration is finished the syringe gauge is released.

8. When the drive head has moved to the extended end position, the syringe gauge can be removed.

9. Close the syringe holder. The device can now be switched off.

Note

If the device is switched off before calibration is terminated, thecalibration is invalid and must be repeated.

Evaluation

1. At the end of calibration the result with all the values is displayed in the frame “Calibration process terminated successfully”.

Fig.: 2 — 24

Fig.: 2 — 25

Fig.: 2 — 26

Perfusor® Space, 1.2 gb 2 — 27

Unit Diagnosis / Calibration 2

1.2

This report can be printed out by pressing the “Print” button.

2. Actuate the “OK” button to finish the calibration process and to store the data in the device.

Fig.: 2 — 27

2 — 28 Perfusor® Space, 1.2 gb

Unit Diagnosis / Calibration 2

1.0

Trouble Shooting

Note

The following trouble shooting cannot be carried outindependently. It is based on the precise observance of the stepsfor the device check (please see „Device Check“ ➨ pg. 2 — 9). Fromthere reference is made to the corresponding trouble shootingsteps.

TS Activity Function If yes If no1 Replace power supply. All LEDs light up for a short moment. UTS 7 TS 2

2 At least one LED lights up for a short moment. TS 3 TS 4

3 Replace the LC display. UTS 7

4 A message is displayed on the LC display. TS 6 TS 5

5 Exchange processor PCB. All LEDs light up for a short moment and a message is displayed on the LC display.

UTS 7 TS 6

6 Exchange operating unit. UTS 8

7 Exchange loudspeaker and switch on unit. A short deep and then a short high beep sound. UTS 10 TS 8

8 Exchange processor PCB. UTS 10

9 Exchange operating unit. Keyboard, LC display as well as the syringe area are illuminated.

UTS 13 TS 10

10 Exchange processor PCB. UTS 13

11 Replace drive. TS 12

12 Switch on unit. The drive head moves to the extended end position. UTS 14 TS 13

13 Exchange processor PCB. UTS 14

14 Replace drive head. TS 15

15 Switch on unit. The claws in the syringe head close and open. UTS 15 TS 16

16 Exchange processor PCB. UTS 15

17 Replace syringe holder with piston brake. “Syringe change / Please insert syringe …” is displayed after the syringe holder has been opened.

UTS 18 TS 18

18 Exchange processor PCB. UTS 18

19 Exchange processor PCB and actuate the „>“ button.

The following service information is displayed:- Brake: stopped by ____- drivetest ok- Size: 35.4 KuP 35.4 FuP

UTS 19 TS 20

20 Exchange operating unit. UTS 19

21 Replace syringe holder with piston brake. TS 22

Table 2 — 7 Trouble shooting (Part 1 of 2)

Perfusor® Space, 1.0 gb 2 — 29

Unit Diagnosis / Calibration 2

1.0

22 Switch on unit and insert syringe. The syringe piston is fastened with the syringe holder blade and the default message is displayed on the LC display.

UTS 19 TS 23

23 Exchange processor PCB. TS 24

24 Switch on unit and insert syringe. The syringe piston is fastened with the syringe holder blade and the default message is displayed on the LC display.

UTS 19 TS 25

25 Exchange piston brake ribbon cable. UTS 19

26 Exchange processor PCB. TS 27

27 Switch on unit, insert syringe and select. The drive head moves to the syringe piston, the claws in the drive head close and the message “Syringe change active / Syringe is caught” is displayed.

UTS 33 TS 28

28 Replace drive head. UTS 33

29 Exchange operating unit. TS 30

30 Test all buttons on the operating unit during a functional check.

When the buttons are pressed the desired reaction is carried out.

UTS 34 TS 31

31 Exchange processor PCB. UTS 35

32 Exchange PCA-slide and lock PCA-lock with PCA-key.

The syringe holder cannot be opened. UTS 59 TS 33

33 Exchange PCA eccentric and lock PCA-lock with PCA-key.

The syringe holder cannot be opened. UTS 59 TS 34

34 Replace syringe holder with piston brake. UTS 59

35 Exchange processor PCB. UTS 65

36 Replace battery module. TS 37

37 Switch on unit and open the battery compartment cover when the drive head has moved to the extended end position.

UTS 67 TS 38

38 Exchange processor PCB. UTS 67

39 Disconnect power supply from the device and switch on device.

All LEDs light up for a short moment. UTS 9 TS 41

40 Charge battery module for about 16 hours in the device with power supply connected.

TS 39

41 Replace battery module. UTS 9

TS Activity Function If yes If no

Table 2 — 7 Trouble shooting (Part 2 of 2)

2 — 30 Perfusor® Space, 1.0 gb

31.0

3 -Disassembly / AssemblyPerfusor® Space

3.1 General Remarks on Disassembly / Assembly

Before disassembling the unit, the system must be checked(please see „Device Check“ ➨ pg. 2 — 9) to isolate the part to beexchanged.

The necessary steps to disassemble the complete unit, all itssubsystems and spare parts are detailed in the followingdescription. Steps that are not necessary can be skipped.

Move the drive head to the extended end position before startingdisassembly.

1. Switch the unit on. The drive head moves to the extended end position.

2. Open the syringe holder.

3. Switch the device off when the syringe holder is opened. The drive head stays at the extended end position.

WARNING

PAY ATTENTION TO THE PISTON BRAKE BLADE WHEN WORKINGON THE PISTON BRAKE. THE BLADE IS SHARP AND MAY CAUSEINJURIES.

Note

Special screws for plastic housings are used in this unit. Payattention to the corresponding notes when you fit the screws.

Perfusor® Space, 1.0 gb 3 — 1

Disassembly / Assembly 3

1.2

Preparations for Exchanging the Processor PCB

If the processor PCB is to be replaced a back-up of the pumpsettings is to be carried out, if this is still possible.

1. Start the Service Program (please see „Starting the Service Program“ ➨ pg. 1 — 8).

2. Select the register tab “Modification data”.

3. Press the “From device“ button. The data is read from the pump.

Fig.: 3 — 1

3 — 2 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.2

4. Select the tab “IO”.

5. Press the “To file“ button.

In the window which opens now you are asked for the storage position of the file on the PC hard disk and the file name.

6. Press the “Print” button to transmit the device data to a printer.

Fig.: 3 — 2

Perfusor® Space, 1.2 gb 3 — 3

Disassembly / Assembly 3

1.2

7. Actuate the “Display“ button to display the device data on screen.

With “Close” the window is closed again.

8. Select the storage position in the “Save as” window and input a unique file name.

9. Press the “Save“ button. The data of the pump is saved on the PC hard disk.

Fig.: 3 — 3

Fig.: 3 — 4

3 — 4 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.2

10. Select the tab “Disposable article”.

11. Actuate the “from device“ button. The data is read from the pump.

The data of the disposable articles read out is displayed on screen.

Fig.: 3 — 5

Perfusor® Space, 1.2 gb 3 — 5

Disassembly / Assembly 3

1.2

12. Press the “Save as“ button.

In the window which opens now you are asked for the storage position of the file on the PC hard disk and the file name.

Fig.: 3 — 6

3 — 6 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.2

13. Select the storage position in the “Save as” window and input a unique file name.

14. Press the “Save“ button. The data of the pump is saved on the PC hard disk.

15. Exit the Service Program (please see „Quit the Service Program“ ➨ pg. 1 — 11).

Note

When the new processor PCB has been installed the saved datamust be transferred back to the device (please see „Processor PCB“➨ pg. 3 — 36).

Fig.: 3 — 7

Perfusor® Space, 1.2 gb 3 — 7

Disassembly / Assembly 3

1.2

Service Parts and Screw Kit

All small parts, such as cover caps, are contained in a Perfusor®Space service part kit.

Designation Ord. No.

Service part kit Perfusor® Space . . . . . . . . . . . . . . . . . 3477 4270with:housing cover cap (40 pieces)cover caps for operating unit (10 pieces)cover cap for syringe holder (10 pieces)cover cap for drive head and claw (20 pieces)housing foot (20 pieces)release button SP with leaf spring (5 pieces)wing sensor holder (2 pieces)locking clip for piston brake (10 pieces)PCA key (2 pieces)

Cover caps for housing SP (50 pieces) . . . . . . . . . . . . . 3477 4386

Cover caps for operating unit PSP (50 pieces) . . . . . . 3477 3103

Connector seal P2 (50 pieces) . . . . . . . . . . . . . . . . . . . 3477 3102

All screws used in the device are included in a Perfusor® Spacescrew kit.

Screw kit Perfusor® Space . . . . . . . . . . . . . . . . . . . . . . 3477 4289with:screw EJOT 22×8 WN 5451 TORX 6IP (5 pieces)screw EJOT 25×7 WN 5451 TORX 8IP (5 pieces)screw EJOT 30×6 WN 5451 TORX 10IP (5 pieces)screw EJOT 30×8 WN 5451 TORX 10IP (10 pieces)screw EJOT 20×12 WN 5452 TORX 6IP (5 pieces)screw EJOT 20×14 WN 5452 TORX 6IP (5 pieces)screw EJOT 22×4.5 WN 5452 TORX 6IP (10 pieces)screw EJOT 25×10 WN 5452 TORX 8IP (5 pieces)screw EJOT 30×8 WN 5452 TORX 10IP (10 pieces)screw EJOT 30×12 WN 5452 TORX 10IP (10 pieces)screw EJOT 30×35 WN 5452 TORX 10IP (5 pieces)screw EJOT 22×8 WN 5454 TORX 6IP (5 pieces)locking ring (5 pieces)

3 — 8 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.0

3.2 Battery Module Designation Ord. No.

Battery compartment cover PSP . . . . . . . . . . . . . . . . . 3452 0872

Battery pack SP (NIMH). . . . . . . . . . . . . . . . . . . . . . . . . 0871 3180

Disassembly

Note

Move the drive head to the extended end position before startingdisassembly (please see „General“ ➨ pg. 3 — 1).

1. Press the lock (Fig.: 3 — 8 / Item 2) on the battery compartment cover (Fig.: 3 — 8 / Item 1) and remove the battery compartment cover.

Note

The battery compartment cover of more recent devices is shorterand can only be unlocked using a pointed object.

Fig.: 3 — 8

Legend of fig. 3 — 8:ItemDesignation

1 Battery compartment cover

2 Battery compartment cover lock

2

1

Perfusor® Space, 1.0 gb 3 — 9

Disassembly / Assembly 3

1.0

2. Lift the lock (Fig.: 3 — 9 / Item 3) on the battery pack (Fig.: 3 -9 / Item 1) and remove the battery pack out of the device.

Fig.: 3 — 9

Legend of fig. 3 — 9:ItemDesignation

1 Battery pack

2 Battery compartment cover

3 Battery pack lock

3

1

2

3 — 10 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

3.3 Unit Foot Designation Ord. No.

Unit foot(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Disassembly

1. Pull the unit foot (Fig.: 3 — 10 / Item 1) out of the housing.

Fig.: 3 — 10

Legend of fig. 3 — 10:ItemDesignation

1 Unit foot

1

Perfusor® Space, 1.0 gb 3 — 11

Disassembly / Assembly 3

1.0

3.4 Operating Unit Designation Ord. No.

Operating unit PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0970

Hinge plate PSP, left . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1011

Hinge plate PSP, right . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1020

PCA-slide PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0899

PCA-eccentric PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0902

Rear panel, operating unit PSP . . . . . . . . . . . . . . . . . . . 3452 1003

LC display SP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0988

Front flap with keyboard PSP . . . . . . . . . . . . . . . . . . . . 3452 0996

Screws and cover caps(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Note

Please pay attention to the corresponding notes during assemblyand installation (please see „Assembly / Installation“ ➨

pg. 3 — 35).

Disassembly

1. Pierce two cover caps (Fig.: 3 — 11 / Item 1) with a small screwdriver and remove cover caps.

2. Unscrew two screws and remove the right hinge plate (Fig.: 3 — 11 / Item 3) carefully out of the bottom part of the housing and pull it off the (Fig.: 3 — 11 / Item 6) operating unit.

Note

When dismounting the operating unit pay attention to the lengthof the connection cable.

3. Remove the PCA-slide (Fig.: 3 — 11 / Item 5) and the PCA-eccentric (Fig.: 3 — 11 / Item 4) out of the housing bottom part.

Fig.: 3 — 11

Legend of fig. 3 — 11:ItemDesignation

1 Cover cap

2 Screw EJOT 30×8 WN 5452 TORX 10IP A2

3 Hinge plate, right

4 PCA-eccentric

5 PCA-slide

6 Operating unit

6

5

4

3

2

1

3 — 12 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

4. Push the right and left connector locks (Fig.: 3 — 12 / Item 2) carefully forward.

5. Disconnect the operating unit connection cable (Fig.: 3 — 12 / Item 1) from the connector.

Fig.: 3 — 12

Legend of fig. 3 — 12:ItemDesignation

1 Operating unit connection cable

2 Connector lock

2

1

Perfusor® Space, 1.0 gb 3 — 13

Disassembly / Assembly 3

1.2

6. Pull the operating unit from the left hinge plate (Fig.: 3 — 13 / Item 3).

7. Pierce two cover caps (Fig.: 3 — 13 / Item 1) with a small screwdriver and remove cover caps.

8. Unscrew two screws and remove the left hinge plate.

Fig.: 3 — 13

Legend of fig. 3 — 13:ItemDesignation

1 Cover cap

2 Screw EJOT 30×8 WN 5452 TORX 10IP A2

3 Hinge plate, left

4 Operating unit

4

3

2

1

3 — 14 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.0

Disassembly

1. Pierce six cover caps (Fig.: 3 — 14 / Item 1) with a small screwdriver and remove cover caps.

2. Unscrew six screws and remove the rear panel (Fig.: 3 — 14 / Item 4).

Note

The three screws of the keyboard must not be loosened. A uniformpressure point of all keys is only guaranteed when a special toolis used for assembly.

Fig.: 3 — 14

Legend of fig. 3 — 14:ItemDesignation

1 Cover cap

2 Screw EJOT 22×4.5 WN 5452 TORX 6IP A2

3 Screws for keyboard: Do not loosen the screws

4 Operating unit rear panel

1 2

4

3

Perfusor® Space, 1.0 gb 3 — 15

Disassembly / Assembly 3

1.0

3. Push the right and left connector locks of the PCB keyboard carefully to the left.

4. Pull the LC display ribbon cable (Fig.: 3 — 16 / Item 1) out of the connector.

5. Lift the LC display out of the operating unit.

Note

The screws of the keyboard must not be loosened. A specialprocedure is required to install the keyboard, so that a uniformpressure point is guaranteed for all keys.

Fig.: 3 — 15

Legend of fig. 3 — 15:ItemDesignation

1 LC display connection cable lock

1

Fig.: 3 — 16

Legend of fig. 3 — 16:ItemDesignation

1 LC display

2 Front flap with keyboard

1

2

3 — 16 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

3.5 Upper Part of Housing Designation Ord. No.

Upper part of housing PSP . . . . . . . . . . . . . . . . . . . . . . 3452 0910

Screws and cover caps(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Note

Please pay attention to the corresponding notes during assemblyand installation (please see „Assembly / Installation“ ➨

pg. 3 — 35).

Disassembly

1. Pierce five cover caps (Fig.: 3 — 17 / Item 4) with a small screwdriver and remove cover caps.

2. Unscrew five screws.

3. Loosen the locking tabs (Fig.: 3 — 17 / Item 1) of the upper part of the housing (Fig.: 3 — 17 / Item 2) carefully by pressing the left and rear outer edge of the housing upwards and remove the housing upper part.

Note

Pay attention to the length of the connection cable and to theconnectors P2 and P3 when dismounting the housing. Do not pullthe connectors together with the upper part out of the bottompart.

Fig.: 3 — 17

Legend of fig. 3 — 17:ItemDesignation

1 Locking tabs

2 Housing upper part

3 Screw EJOT 30×35 WN 5452 TORX 10IP A2

4 Cover cap

5 Screw EJOT 30×12 WN 5452 TORX 10IP A2

2

5 4 3

1

Perfusor® Space, 1.0 gb 3 — 17

Disassembly / Assembly 3

1.0

4. Unscrew two screws and remove the contact strip (Fig.: 3 -18 / Item 3) (Fig.: 3 — 18 / Item 1).

Note

If necessary, the spring-mounted contact pins must be carefullyinserted when the contact strip is dismounted.

Fig.: 3 — 18

Legend of fig. 3 — 18:ItemDesignation

1 Housing upper part

2 Screw EJOT 25×7 WN 5451 TORX 8IP

3 Contact strip

1

23

3 — 18 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

3.6 Release Button Designation Ord. No.

Release button PSP with leaf spring(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Disassembly

1. Pull the release button (Fig.: 3 — 19 / Item 1) out of the housing bottom part.

3.7 Loudspeaker Designation Ord. No.

Loudspeaker SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0937

Disassembly

1. Pull the loudspeaker connector off (Fig.: 3 — 20 / Item 1) the processor PCB and remove the loudspeaker.

Fig.: 3 — 19

Legend of fig. 3 — 19:ItemDesignation

1 Release button

1

Fig.: 3 — 20

Legend of fig. 3 — 20:ItemDesignation

1 Loudspeaker

1

Perfusor® Space, 1.0 gb 3 — 19

Disassembly / Assembly 3

1.0

3.8 Drive Designation Ord. No.

Drive PSP, cpl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1046

Drive head PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1038(incl. driving tube)

Claw mechanism PSP . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1550

Drive PCB, PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1569

Side part of housing PSP . . . . . . . . . . . . . . . . . . . . . . . . 3452 1054

Screws(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Note

Please pay attention to the corresponding notes during assemblyand installation (please see „Assembly / Installation“ ➨

pg. 3 — 35).

Disassembly

1. Tilt the lock (Fig.: 3 — 21 / Item 1) of the drive ribbon cable upwards and pull the cable out of the connector.

2. Loosen one screw (Fig.: 3 — 23 / Item 1) and lift the fastening angle (Fig.: 3 — 23 / Item 2) of the drive ribbon cable.

3. Unscrew one screw (Fig.: 3 — 23 / Item 3) and remove the screw together with the locking washer (Fig.: 3 — 23 / Item 4) from the drive.

4. Pull the left carrier (Fig.: 3 — 22 / Item 1) / (Fig.: 3 — 23 / Item 5) out of the drive slide.

5. Pull out the drive head (Fig.: 3 — 23 / Item 6) together with the driving tube and the guide rail carefully from the drive assembly.

CAUTION

Pay attention to the ribbon cable in the driving tube whendismounting the drive.

Fig.: 3 — 21

Legend of fig. 3 — 21:ItemDesignation

1 Drive connector lock

1

Fig.: 3 — 22

Legend of fig. 3 — 22:ItemDesignation

1 Left carrier

1

3 — 20 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.1

Fig.: 3 — 23

Legend of fig. 3 — 23:ItemDesignation

1 Screw EJOT 22×8 WN 5451 TORX 6IP A2

2 Fastening angle

3 Screw EJOT 22×8 WN 5451 TORX 6IP A2

4 Washer

5 Carrier

6 Drive head

1 2

6

345

Perfusor® Space, 1.1 gb 3 — 21

Disassembly / Assembly 3

1.0

6. Pull the drive motor connector (Fig.: 3 — 24 / Item 2) off the processor PCB.

7. Unscrew one screw (first temporary screw) and remove the processor PCB ground cable (Fig.: 3 — 24 / Item 3).

Fig.: 3 — 24

Legend of fig. 3 — 24:ItemDesignation

1 Screw EJOT 30×8 WN 5451 TORX 10IP

2 Drive motor connector

3 Processor PCB ground cable

1 3 2

3 — 22 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

8. Unscrew one screw (second temporary screw) and take the drive assembly (Fig.: 3 — 25 / Item 1) out of the housing.

Note

Please pay attention to the corresponding notes during assemblyand installation (please see „Assembly / Installation“ ➨

pg. 3 — 35).

9. Pull the side part of the housing (Fig.: 3 — 26 / Item 1) out of the bottom part.

Fig.: 3 — 25

Legend of fig. 3 — 25:ItemDesignation

1 Drive assembly

2 Screw EJOT 30×8 WN 5451 TORX 10IP

2

1

Fig.: 3 — 26

Legend of fig. 3 — 26:ItemDesignation

1 Side part of housing

1

Perfusor® Space, 1.0 gb 3 — 23

Disassembly / Assembly 3

1.1

Disassembly of the Drive Head

1. Pierce two cover caps (Fig.: 3 — 27 / Item 4) with a small screwdriver and remove cover caps.

2. Unscrew two screws (Fig.: 3 — 27 / Item 3).

3. Remove claws (Fig.: 3 — 27 / Item 2) carefully out of the drive head.

CAUTION

The membrane plate (Fig.: 3 — 27 / Item 1) of the drive head mustnot be used as thrust bearing when removing the claws. If theforce exerted on the membrane plate is too great the membraneplate and the accessory components are damaged.

4. Pierce three cover caps (Fig.: 3 — 28 / Item 2) with a small screwdriver and remove cover caps.

5. Unscrew three screws (Fig.: 3 — 28 / Item 1).

6. Pull the drive head housing (Fig.: 3 — 28 / Item 3) over the driving tube and off the drive head.

Note

Note cable- or wire layout and sketch if necessary.

Fig.: 3 — 27

Legend of fig. 3 — 27:ItemDesignation

1 Membrane plate

2 Claws

3 Screw EJOT 20×18 WN 5452 TORX 6IP

4 Cover caps

4 3 2

1

Fig.: 3 — 28

Legend of fig. 3 — 28:ItemDesignation

1 Screw EJOT 25×10 WN 5452 A2 TORX 6IP

2 Cover caps

3 Drive head housing

21

3

3 — 24 Perfusor® Space, 1.1 gb

Disassembly / Assembly 3

1.1

7. Pull the claw mechanism (Fig.: 3 — 29 / Item 3) off the drive head cover (Fig.: 3 — 29 / Item 2) until the connection cable connector (Fig.: 3 — 29 / Item 1), (Fig.: 3 — 30 / Item 1) can be easily accessed.

8. Pull the connection cable of the claw mechanism off the drive head PCB and remove the claw mechanism.

9. Tilt the lock (Fig.: 3 — 30 / Item 3) of the drive ribbon cable upwards and pull the cable out of the connector.

Note

Pay attention to the emergency release tappet (Fig.: 3 — 30 /Item 2) during disassembly. The emergency release tappet caneasily drop out of the guide.

Fig.: 3 — 29

Legend of fig. 3 — 29:ItemDesignation

1 Connection cable, claw mechanism

2 Drive head cover

3 Claw mechanism

3

2

1

Fig.: 3 — 30

Legend of fig. 3 — 30:ItemDesignation

1 Connector of claw mechanism connection cable

2 Emergency release tappet

3 Ribbon cable, drive

1

3

2

Perfusor® Space, 1.1 gb 3 — 25

Disassembly / Assembly 3

1.2

10. Unscrew one screw (Fig.: 3 — 31 / Item 2) and remove the ground wire (Fig.: 3 — 31 / Item 1) of the drive PCB (Fig.: 3 -31 / Item 3) from the driving tube.

CAUTION

Pay attention to the strain gauge (Fig.: 3 — 31 / Item 4) whendismantling the drive head PCB. The strain gauge must not bejammed or removed by force out of the drive head cover.

CAUTION

The PCB potentiometer of the drive head must not be turned bymore than approx. 120°.

11. Take the drive PCB with the strain gauge carefully out of the drive head cover. The strain gauge and the PCB should be pulled vertically out of the holder.

Fig.: 3 — 31

Legend of fig. 3 — 31:ItemDesignation

1 Ground wire

2 Screw EJOT-PT Type DG 22×5 WN 1552

3 Drive PCB

4 Strain gauge

21

34

3 — 26 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.0

3.9 Syringe Holder with Piston Brake Designation Ord. No.

Piston brake PSP ribbon cable. . . . . . . . . . . . . . . . . . . . 3452 0864

Syringe holder with piston brake PSP, cpl. . . . . . . . . . . 3452 0945

Syringe holder PSP spring . . . . . . . . . . . . . . . . . . . . . . . 3452 0953

Piston brake PSP guide rail . . . . . . . . . . . . . . . . . . . . . . 3452 0961

Screws and cover caps(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Disassembly

WARNING

PAY ATTENTION TO THE PISTON BRAKE BLADE WHEN WORKINGON THE PISTON BRAKE. THE BLADE IS SHARP AND MAY CAUSEINJURIES.

1. Push the right and left connector lock (Fig.: 3 — 32 / Item 1) on the processor PCB carefully forward.

2. Pull the ribbon cable (Fig.: 3 — 32 / Item 2) out of the connector.

Fig.: 3 — 32

Legend of fig. 3 — 32:ItemDesignation

1 Processor PCB connector lock

2 Piston brake ribbon cable

1 2

Perfusor® Space, 1.0 gb 3 — 27

Disassembly / Assembly 3

1.0

3. Unscrew one screw and remove the locking clip (Fig.: 3 — 33 / Item 2) from the piston brake PCB.

Fig.: 3 — 33

Legend of fig. 3 — 33:ItemDesignation

1 Screw EJOT 20×14 WN 5452 TORX 6IP

2 Locking clip

1

2

3 — 28 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

4. Open the right and left connector lock (Fig.: 3 — 34 / Item 1) on the piston brake PCB carefully.

5. Pull the ribbon cable (Fig.: 3 — 35 / Item 1) out of the connector and remove the cable from the housing.

Fig.: 3 — 34

Legend of fig. 3 — 34:ItemDesignation

1 Piston brake connector lock

1

Fig.: 3 — 35

Legend of fig. 3 — 35:ItemDesignation

1 Piston brake ribbon cable

1

Perfusor® Space, 1.0 gb 3 — 29

Disassembly / Assembly 3

1.0

6. Remove the syringe holder spring (Fig.: 3 — 36 / Item 1) from the post in the bottom part of the housing.

Note

The syringe holder spring can only be removed together with thepiston brake drive.

7. Pull out the syringe holder and turn it clockwise.

8. Pierce two cover caps (Fig.: 3 — 37 / Item 2) in the syringe holder with a small screwdriver and remove cover caps.

9. Unscrew two screws and remove the cover from the syringe holder (Fig.: 3 — 37 / Item 1).

10. Turn and push in the syringe holder housing with piston brake.

Fig.: 3 — 36

Legend of fig. 3 — 36:ItemDesignation

1 Syringe holder spring

1

Fig.: 3 — 37

Legend of fig. 3 — 37:ItemDesignation

1 Syringe holder cover

2 Cover cap

3 Screw EJOT 25×10 WN 5452 TORX 8IP

1

3 2

3 — 30 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

11. Drive the piston brake motor with maximum 3 V DC. The blade is moved out of the syringe holder housing.

Note

If the blade moves into the syringe holder housing, then thepolarity on the piston brake motor must be changed.

12. Pull the blade out of the syringe holder housing.

13. Loosen one screw. Remove the piston brake PCB (Fig.: 3 — 39 / Item 2) and put it carefully aside. The connection wires must not be unsoldered.

Note

Pay attention to the light barrier components on the PCBunderside and to the length of the connection wires to the pistonbrake motor when removing the printed circuit board.

Fig.: 3 — 38

Legend of fig. 3 — 38:ItemDesignation

1 Piston brake blade

1

Fig.: 3 — 39

Legend of fig. 3 — 39:ItemDesignation

1 Screw EJOT 20×12 WN 5452 TORX 6IP

2 Piston brake PCB

1

2

Perfusor® Space, 1.0 gb 3 — 31

Disassembly / Assembly 3

1.0

14. Unscrew one screw and remove the bearing cover (Fig.: 3 -40 / Item 2).

15. Take the lock (Fig.: 3 — 40 / Item 3) out of the bearing housing.

16. Open the circlip (Fig.: 3 — 41 / Item 3) and pull it together with the carrier (Fig.: 3 — 41 / Item 2) off the syringe holder housing (Fig.: 3 — 41 / Item 1).

17. Pull the syringe holder housing out of the bottom part of the housing.

Fig.: 3 — 40

Legend of fig. 3 — 40:ItemDesignation

1 Screw EJOT 20×12 WN 5452 TORX 6IP

2 Bearing cover

3 Lock

3

2

1

Fig.: 3 — 41

Legend of fig. 3 — 41:ItemDesignation

1 Syringe holder housing

2 Carrier

3 Circlip

12 3

3 — 32 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.0

18. Unscrew two screws and remove guide rail (Fig.: 3 — 42 / Item 2) out of the bottom part of the housing.

19. Take piston brake motor assembly (Fig.: 3 — 42 / Item 4) out of the housing bottom part.

20. Remove syringe holder spring from the piston brake motor assembly.

Fig.: 3 — 42

Legend of fig. 3 — 42:ItemDesignation

1 Screw EJOT 30×8 WN 5451 TORX 10IP

2 Guide rail

3 Syringe holder spring

4 Piston brake motor assembly

1

2

4

3

Perfusor® Space, 1.0 gb 3 — 33

Disassembly / Assembly 3

1.1

3.10 Processor PCB Designation Ord. No.

Processor PCB PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0880(incl. connectors andsyringe wing sensor)

Housing bottom part PSP . . . . . . . . . . . . . . . . . . . . . . . 3452 0929

Type plate PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Upon request

Screws and syringe wing sensor holder(please see „Service Parts and Screw Kit“ ➨ pg. 3 —

Note

Please pay attention to the corresponding notes during assemblyand installation (please see „Assembly / Installation“ ➨

pg. 3 — 35).

Disassembly

1. Pull the syringe wing sensor holder (Fig.: 3 — 43 / Item 1) out of the housing.

2. Lift the syringe wing sensor (Fig.: 3 — 43 / Item 6) out of the housing bottom part (Fig.: 3 — 43 / Item 5).

Note

Pay attention to the connection cable to the syringe wing sensorwhen removing the processor PCB. The connection cable is notshown in Fig.: 3 — 43.

3. Unscrew three screws and remove screws together with the processor PCB (Fig.: 3 — 43 / Item 2) and the shielding plate (Fig.: 3 — 43 / Item 4) from the bottom part of the housing.

Fig.: 3 — 43

Legend of fig. 3 — 43:ItemDesignation

1 Syringe wing sensor holder

2 Processor PCB

3 Screw EJOT 30×6 WN 5451 TORX 10IP

4 Shielding plate with earthing wire

5 Housing bottom part

6 Syringe wing sensor

32

6

5

1

4

3 — 34 Perfusor® Space, 1.1 gb

Disassembly / Assembly 3

1.0

3.11 Assembly / Installation Assembly or installation of the modules and subsystems is done inreverse order of disassembly. Special steps to be observed aredescribed hereafter in detail.

Only new cover caps are to be used.

Special Screws

Special screws for plastic housings are used in this unit. Thescrews are not self-cutting but produce a thread in the plastic ofthe housing through deformation when fitted in for the first time.

If the beginning of the thread is not engaged when the screw isfitted, a new thread is produced and the old thread is destroyedso that the security of the fixing can no longer be guaranteed.

Proceed as follows to fit the special screws:

1. Put the screw on the thread.

2. Rotate screw anti-clockwise (loosen) until a faint click can be heard. This click is produced when the screw thread drops into the existing thread.

3. Screw in the screw and tighten with the defined torque.

Zero Force Insertion Connector

Note

Make sure that the ribbon cable is centered between the plugguides when the zero force insertion connector is locked. Checkthe lock and the ribbon cable for correct fit before any furtherinstallation.

Perfusor® Space, 1.0 gb 3 — 35

Disassembly / Assembly 3

1.1

Processor PCB

When the processor PCB is replaced all data of the pump exceptfor the calibration data was probably saved on a PC. (please see„Preparations for Exchanging the Processor PCB“ ➨ pg. 3 — 2)Carry out the following steps to transmit the data back to thedevice.

WARNING

WHEN DATA PREVIOUSLY SAVED IS TRANSFERRED BACK TO THEDEVICE, CALIBRATION DATA IS NOT TRANSFERRED. THEREFORE, ACOMPLETE NEW CALIBRATION OF THE UNIT IS REQUIRED.

1. Start the Service Program (please see „Starting the Service Program“ ➨ pg. 1 — 8).

2. Select the register tab “Modification data”.

3. Press the “from file“ button. The window “Open” is displayed on screen.

3 — 36 Perfusor® Space, 1.1 gb

Disassembly / Assembly 3

1.2

4. Select the desired file with the mouse pointer and press the “Open” button.

Fig.: 3 — 44

Fig.: 3 — 45

Perfusor® Space, 1.2 gb 3 — 37

Disassembly / Assembly 3

1.2

5. Change to the tab „IO“ and actuate the “To device“ button. The data is saved in the Perfusor® Space.

6. Press the “OK“ button when the window “Confirmation“ is displayed.

Fig.: 3 — 46

Fig.: 3 — 47

3 — 38 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.2

7. Enter your worker id in the window “Worker ID“. Press the “OK” button to transmit the data to the device.

A message is displayed that a change of the device data may affect the patients.

Fig.: 3 — 48

Fig.: 3 — 49

Perfusor® Space, 1.2 gb 3 — 39

Disassembly / Assembly 3

1.2

8. Select the tab “Disposable article”.

9. Press the “Load from“ button. The window “Open” is displayed on screen.

Fig.: 3 — 50

3 — 40 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.2

10. Select the desired file with the mouse pointer and press the “Open” button. The data loaded is displayed on screen.

11. Actuate the “To device“ button. The data is saved in the Perfusor® Space.

Fig.: 3 — 51

Fig.: 3 — 52

Perfusor® Space, 1.2 gb 3 — 41

Disassembly / Assembly 3

1.2

12. Press the “OK“ button when the window “Confirmation“ is displayed.

13. Enter your user number in the window “User number“. Press the “OK” button to transmit the data to the device.

A message is displayed that a change of the device data may affect the patients.

14. Exit the Service Program (please see „Quit the Service Program“ ➨ pg. 1 — 11).

Fig.: 3 — 53

Fig.: 3 — 54

Fig.: 3 — 55

3 — 42 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.1

Loudspeaker

1. Route the loudspeaker connection cable between the drive motor and its connection wires, see Fig.: 3 — 56.

Piston Brake

WARNING

PAY ATTENTION TO THE PISTON BRAKE BLADE WHEN WORKINGON THE PISTON BRAKE. THE BLADE IS SHARP AND MAY CAUSEINJURIES.

Note

Pay attention to the light barrier components on the PCBunderside when installing the piston brake PCB.

1. Insert the syringe holder spring on the piston brake drive and fit the drive.

2. Route the ribbon cable to the piston brake drive as shown in Fig.: 3 — 57.

Fig.: 3 — 56

Fig.: 3 — 57

Perfusor® Space, 1.1 gb 3 — 43

Disassembly / Assembly 3

1.2

Drive Head

1. Insert the drive head PCB with the strain gauge vertically in the drive head cover. Please note that the strain gauge must not get jammed in the guide.

Note

The three strain gauge tongues are level with the PCB upper side.

2. The ground wire is to be layed according to the notes or the draft which was prepared before disassembly.

3. Turn the potentiometer (Fig.: 3 — 58) of the drive head PCB before assembly in such a way that the operating square of the upper claw seat can be pushed in.

CAUTION

The PCB potentiometer of the drive head must not be turned bymore than approx. 120°.

4. Position the two claw seats (Fig.: 3 — 58) before assembly in such a way that the marking (dot in material) on the upper claw seat points vertically upwards and the marking on the bottom claw seat points to the right, away from the driving tube.

Note

The motor connection wires and the ground wire must be laidbetween the claw mechanism bearing and the driving tube so thatthey cannot slip in the area of moving parts, e.g. the membranetappet.

Fig.: 3 — 58

Fig.: 3 — 59

3 — 44 Perfusor® Space, 1.2 gb

Disassembly / Assembly 3

1.1

Note

Check the position of the emergency release tappet beforemounting the drive head housing.

5. Push the drive head housing on to the driving tube until the switch flag of the membrane tappet is positioned just before the claw mechanism.

6. Turn the switch flag in such a way that it can be pushed in the switch flag guide.

7. Now mount the drive head housing. The membrane tappet must engage in the claw mechanism when the drive head housing is installed. For this purpose the membrane can be pressed during or after assembly.

Note

Pay attention that the membrane can be moved smoothly.

8. Install both claws and make sure that the sealing lips are not squeezed or damaged.

Drive / Side Part of Housing

Note

Take care not to damage the ribbon cable when inserting thedriving tube into the drive assembly.

Note

Pay attention to the switch on the processor PCB when mountingthe drive. The switch should be operated by the drive assemblyslide.

Fig.: 3 — 60

Fig.: 3 — 61

Perfusor® Space, 1.1 gb 3 — 45

Disassembly / Assembly 3

1.1

Note

Pay attention to the syringe wing sensor when inserting the sidepart of the housing and make sure that the sensor can be operatedcorrectly.

1. Route the ribbon cable through the slide nut before pushing in the driving tube and then through the slide in front of the spindle nut when looking from the rear of the housing.

2. Fold the ribbon cable once through 90° upwards, see Fig.: 3 -62, before mounting the fastening angle.

3. Run the drive motor connector over the loudspeaker connection cable. The loudspeaker connection cable must be positioned between the drive motor housing and the motor connection wires.

Note

Check that the two carriers in the drive slide are protected fromfalling out by the washer and screw.

Housing

Note

Take care that no cables are squeezed, and check that theconnector seals at the back are correctly placed in the housingand that the loudspeaker is correctly located when the housing isfitted.

1. Before mounting check the silicone seals in the housing and grease with silicone high-vacuum grease (part No. 3450 7930).

2. Lower the upper part of the housing vertically and carefully on to the bottom part.

3. Press the upper and bottom parts of the housing carefully together so that the outer edges engage. The locking tabs must click together.

Fig.: 3 — 62

3 — 46 Perfusor® Space, 1.1 gb

Disassembly / Assembly 3

1.0

Operating Unit

Note

Before fitting the rear panel check the screw lengths. The screwsmay only be 4.5 mm long (without head). Longer screws must beexchanged.

Note

Before mounting the operating unit check the plastic foamgaskets in the housing opening for the connection cable to theoperating unit.

1. Attach the left hinge plate to the operating unit, press it into the bottom part of the housing and install the hinge plate.

2. Push the operating unit connection cable into the processor PCB connector. Lock the connector.

3. Insert the PCA-slide and the PCA-eccentric in the bottom part of the housing.

4. Attach the right hinge plate to the operating unit and fit the hinge plate and the operating unit into the bottom part of the housing. Press the PCA-eccentric backwards until it slides into the opening on the right hinge plate.

Checks after Repair Procedure

1. Carry out a calibration after having worked on the drive, the syringe holder with piston brake or the processor PCB while the device was opened (please see „Calibration“ ➨ pg. 2 — 14).

2. Check the device to ensure safe functionality of the unit (please see „Device Check“ ➨ pg. 2 — 9).

3. Depending on the work carried out the specific steps of the TSC must be performed (please see „Technical Safety Check (TSC)“ ➨ pg. 5 — 1).

Perfusor® Space, 1.0 gb 3 — 47

Disassembly / Assembly 3

1.0

Check List for Checks after Repair

Visual Inspection Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751

Functional Inspection

❒ Cleanliness❒ Completeness❒ Damage and faults affecting safety❒ Damage to and readability of the label❒ Syringe holder with piston brake❒ Screw covers❒ Connectors “P2” and “P3”

The patient and housing leakage current ofthe Perfusor® Space is caused exclusively bythe operating voltage supply (Power SupplySP or SpaceStation). The Technical Safety Checks of the powersupply SP (drawing No. M001 32 10 05 F04)or of the SpaceStation (drawing No. M69000 00 46 F04) serve to check whether bothlimit values are met.

❒ Locking with second unit❒ Operating unit magnets❒ Battery compartment cover

Switch on unit with power supply❒ Self-test❒ Indicator lamps (LEDs)❒ Audible alarm❒ Status display❒ Lighting of syringe compartment

Operation❒ Syringe fastening❒ Syringe recognition❒ Infusion❒ Staff call❒ Bolus❒ PCA lock

Switch on unit without power supply❒ Self-test❒ Magnetic function of the battery

compartment cover❒ Charge state of the battery module

(Part 1 of 2)

3 — 48 Perfusor® Space, 1.0 gb

Disassembly / Assembly 3

1.1

Pressure cut off according to TSCSyringe type: «#Lehre OPS50“Delivery rate: 200 ml/h

WARNING

REMOVE SYRINGE GAUGE ONLY WHENRELEASED. DANGER OF INJURY!

Strain gauge pressure measurement❒ Pressure stage 1 _______ N❒ Pressure stage 3 _______ N❒ Pressure stage 8 _______ N

Motor power limitation(convert syringe gauge)❒ Pressure stage 1 _______ N❒ Pressure stage 3 _______ N❒ Pressure stage 6 _______ N

Visual Inspection Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751

Functional Inspection

(Part 2 of 2)

Perfusor® Space, 1.1 gb 3 — 49

Disassembly / Assembly 3

1.0

For your notes:

3 — 50 Perfusor® Space, 1.0 gb

41.2

4 -Servicing the Unit

Cleaning Clean and disinfect the Perfusor® Space with a humid cloth at

regular intervals. To clean the system we recommend mild soap-suds.

WARNING

WHILE CLEANING AND DISINFECTING THE PERFUSOR® SPACE,DISCONNECT THE UNIT FROM THE MAINS SUPPLY.

CAUTION

Take care that no water or liquid enters the device along thesyringe holder or the driving tube.

For disinfection by wiping, you should use for exampleMeliseptol® from B. Braun. Allow the unit to dry for at least oneminute. When you disinfect the device by spraying, make sure notto spray in the system openings (such as interface sockets andconnectors, loudspeaker opening).

Servicing the Battery The instructions for use contain a detailed description on how toservice the battery.

If a battery module is not discharged completely for more than 28days, a servicing program for the battery module can be startedon the unit.

Perfusor® Space, 1.2 gb 4 — 1

Servicing the Unit 4

1.0

For your notes:

4 — 2 Perfusor® Space, 1.0 gb

1.0

5 -Technical Safety Check (TSC)Perfusor® Space

Index b(Master — to be added to the documentation)

Checklist for Technical Safety Check – Every 24 Months

Unit: Perfusor® SpaceManufacturer: B. Braun Melsungen AG

User

Observe the Service Manual and the instructions for use. All measured values are to be documented. Accessories used should be included in testing. Make exclusive use of calibrated measuring equipment.

Article No. Unit No. Year of Procurement

Visual Inspection Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751

Functional Inspection

❒ Perfusor® Space:Cleanliness, completeness, damage and faults affecting safety, damage and readability of the labelParticularly:❒ Syringe holder with blade❒ Syringe fastening❒ Membrane in drive head❒ Axial clearance of drive❒ Screw covers❒ Connectors “P2” and “P3”

❒ Accessories:Cleanliness, completeness, damage and faults affecting safety, damage and readability of the label

❒ Check the unit and the accessories for compatibility

The patient and housing leakage current ofthe Perfusor® Space is caused exclusively bythe operating voltage supply (Power SupplySP or SpaceStation). The Technical Safety Checks of the powersupply SP (drawing No. M001 32 10 05 F04)or of the SpaceStation (drawing No. M69000 00 46 F04) serve to check whether bothlimit values are met.

❒ Locking with second unit❒ Operating unit magnets❒ Battery compartment cover

Switch on unit with power supply❒ Self-test❒ Indicator lamps (LEDs)❒ Audible alarm❒ Visual alarm❒ Status display❒ Lighting

Operation❒ Syringe fastening❒ Syringe recognition❒ Infusion❒ Buttons on the operating unit❒ Staff call❒ Bolus❒ PCA lock

Switch on unit without power supply❒ Self-test❒ Magnetic function of the battery

compartment cover

(Part 1 of 2)

Perfusor® Space, 1.0 gb 5 — 1Sheet 1 of 2

M688 70 01 05 F04 / 3891 7319 (GB)

Technical Safety Check (TSC)

Index b(Master — to be added to the documentation)

1.1

Pressure cut-offSyringe type: «#Lehre OPS50″Delivery rate: 200 ml/h

— Strain gauge pressure measurement❒ Pressure stage 1 (11 … 16 N) ______ N❒ Pressure stage 3 (27 … 33 N) ______ N❒ Pressure stage 8 (68 … 76 N) ______ N❒ Error message “Alarm / pressure too

high” at every pressure stage

— Motor power limitation❒ Pressure stage 1 (12 … 27 N) ______ N❒ Pressure stage 3 (32 … 48 N) ______ N❒ Pressure stage 6 (61 … 79 N) ______ N❒ Error message “Alarm / drive blocked”

at every pressure stage

Mechanical Aids and Measuring Equipment Used

Accessories Used

❒ Syringe gauge, serial No.___________Calibrated on____________________

❒ Service connector SP❒ ____________________________❒ ____________________________

❒ Power Supply SP _______________❒ Battery module__________________❒ Staff call lead _______________❒ ____________________________❒ ____________________________

Test result:

Defects found which could endanger patients, users or third parties: Yes No

Inspection performed by:

Measures to be taken: Repair ___________________

Unit handed over on:

Special features / documentation:To:

Date / Signature:

Next deadline for TSC:

Visual Inspection Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751

Functional Inspection

(Part 2 of 2)

5 — 2 Perfusor® Space, 1.1 gbSheet 2 of 2

M688 70 01 05 F04 / 3891 7319 (GB)

1.2

6 -Technical Safety Check (TSC)Power Supply SP

Index c(Master — to be added to the documentation)

Checklist for Technical Safety Check – Every 24 Months

Unit: Power Supply SPManufacturer: B. Braun Melsungen AG

User

Observe the Service Manual and the instructions for use of the respective device. All measured values are to be documented. Make exclusive use of calibrated measuring equipment.

Article No. Unit No. Year of Procurement

Visual Inspection Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751

Functional Inspection

❒ Power Supply SP:Cleanliness, completeness, damage and faults affecting safety, damage and readability of the label

❒ Connecting lineCleanliness, damage and faults affecting safety

❒ Mains voltage ____ V~ (AC)❒ Leakage current ≤ 7 µA ____ µA

Measurement is to be carried out with service adapter SP between primary and secondary circuit.

Note

This measurement ensures that theadmissible limit values regarding thepatient and housing leakage current of thePerfusor® Space or the Infusomat® Spaceare met.

❒ Connector locking❒ After connecting the power supply the

respective unit displays that it is operated in mains operation

❒ Check of power supply, ord. — no. 3310 2708:Check lock of primary adapter with power supply. The adapter must engage on both sides.

Mechanical Aids and Measuring Equipment Used

❒ Perfusor® Space, serial No. _________❒ Infusomat® Space, serial No.:________❒ _____________________________

Test result:

Defects found which could endanger patients, users or third parties: Yes No

Inspection performed by:

Measures to be taken: none Dispose of power supply SP

Unit handed over on:

Special features / documentation:To:

Date / Signature:

Next deadline for TSC:

Perfusor® Space, 1.2 gb 6 — 1Sheet 1 of 2

M001 32 10 05 F04 / 3891 6142 (GB)

Technical Safety Check (TSC)

Index c(Master — to be added to the documentation)

1.0

For your notes:

6 — 2 Perfusor® Space, 1.0 gbSheet 2 of 2

M001 32 10 05 F04 / 3891 6142 (GB)

71.0

7 -Procedural Instructions on the TSC

Visual Inspection Perfusor® Space

1. Check the Perfusor® Space and accessories for cleanliness.

2. Check the Perfusor® Space and accessories for completeness and check configuration.

3. Check the Perfusor® Space and its accessories for damage and the labels for readability. Pay special attention to the following parts:

a) Syringe holder with piston brake

b) Piston brake blade in syringe holder

c) Membrane in drive head(cracks, porous)

d) Axial play of drive

e) Screw covers

f) Connectors “P2” and “P3”

Power Supply SP

1. Check the Power Supply SP and connecting line for cleanliness.

2. Check the Power Supply SP incl. connecting line for damage and the labels for readability.

Perfusor® Space, 1.0 gb 7 — 1

Procedural Instructions on the TSC 7

1.1

Electrical Safetyaccording to IEC/EN 60601-1or VDE 0750 and VDE 0751

Perfusor® Space

The patient and housing leakage current of the Perfusor® Space iscaused exclusively by the operating voltage supply (Power SupplySP or SpaceStation).

The Technical Safety Checks of the power supply SP (drawing No.M001 32 10 05 F04) or of the SpaceStation (drawing No. M69000 00 46 F04) serve to check whether both limit values are met.

Power Supply – Leakage Current

Note

The values to be measured are indicated in the TSC (please see„Technical Safety Check (TSC)“ ➨ pg. 5 — 1).

The leakage current is to be measured between primary andsecondary circuit using the service adapter SP.

Designation Ord. No.

Service adapter SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5174

Check

1. Select leakage current on the testing equipment.

2. Bridge pins 6, 7 12 and 13 with service adapter SP at the connector to the unit.

3. Measure value.

4. Measure value with reverse polarity of the mains connection.

5. Document the largest value.

Fig.: 7 — 1

Legend of fig. 7 — 1:ItemDesignation

1 Mains connection

2 Primary of the power supply

3 Secondary of the power supply

4 Service adapter SP with probe

5 Leakage current measuring device

1 2 43

5

7 — 2 Perfusor® Space, 1.1 gb

Procedural Instructions on the TSC 7

1.0

Functional Inspection Perfusor® Space Mechanical Inspection

1. Fit the unit to be tested on top of another Space device and check the proper functioning of the lock.

2. Fit the unit to be tested under another Space device and check the proper functioning of the lock.

3. Hold the device with the operating unit downwards. The operating unit must not open.

4. Check the battery compartment cover lock for proper operation.

Functional Check

Note

Carry out the check with power supply connected.

1. Switch on unit and check the following details:

— Self-testDisplay on the LC display

— Indicator lampsLEDs (yellow, green, blue) light up for a short moment

— Visual alarmRed LED lights up for a short moment

— Audible alarmA deep and a high sound

— Staff callDepending on the device settings, the red LED on service connector SP lights up permanently or for one second after an alarm was triggered

— Status displayBattery capacity, mains operation (service connector SP)

— LightingIllumination of syringe compartment, LC display and buttons

2. Syringe fastening

a) Axial fastening holds syringe wing

b) Syringe holder blade fixes syringe piston

c) Both claws in drive head catch the syringe piston plate

Perfusor® Space, 1.0 gb 7 — 3

Procedural Instructions on the TSC 7

1.0

3. Check syringe recognition.

a) Insert approved 2 ml / 3 ml syringe.The syringe size is recognized.

b) Insert approved 50 ml syringe.The syringe size is recognized.

4. Carry out infusion and bolus with any syringe and press all buttons at least once.Infusion and bolus are performed and all buttons trigger the function desired.

5. Staff call

a) Plug service connector SP on connector “P2”.

b) Open syringe holder while the infusion is administered.The red LED on the service connector SP lights up.

6. PCA lock

a) Check the PCA lock with an approved 30 ml syringe.

Battery Check

1. Switch device off.

2. Pull off the power supply.

3. Switch on unit.Self-test is carried out.

4. Open battery compartment cover during operation.An alarm is activated.

Pressure Cut-Off (Strain Gauge Pressure Measurement)

WARNING

DURING THE STRAIN GAUGE MEASUREMENT WITH SYRINGEGAUGE THE SYRINGE HOLDER MUST NOT BE OPENED. THESYRINGE GAUGE IS UNDER VERY HIGH PRESSURE AND MAYCAUSE INJURIES IF THE PRESSURE IS RELIEVED SUDDENLY.

1. Plug service connector SP on connector “P2”.

2. Insert syringe gauge and select syringe type “#Lehre OPS 50“.

3. Input a delivery rate of 200 ml/h.

4. Select pressure stage according to the TSC and start infusion.Read off value on the syringe gauge upon an alarm and compare with the specifications in the TSC.

7 — 4 Perfusor® Space, 1.0 gb

Procedural Instructions on the TSC 7

1.0

Pressure Cut-Off (Motor Power Limitation)

WARNING

WHILE CHECKING THE MOTOR POWER LIMITATION WITH THESYRINGE GAUGE THE SYRINGE HOLDER MUST NOT BE OPENED.THE SYRINGE GAUGE IS UNDER VERY HIGH PRESSURE AND MAYCAUSE INJURIES IF THE PRESSURE IS RELIEVED SUDDENLY.

1. Plug service connector SP on connector “P2”.

2. Insert motor power test adapter at drive head.

3. Disassemble push-button plate for Perfusor® Space from syringe gauge, insert syringe gauge and select syringe type “#Lehre OPS50“.

Note

The threaded end of the syringe gauge must be introduced in theopening of the motor power test adapter. Hold on to syringegauge – if necessary by hand – in the syringe area, until thethreaded end of the syringe gauge is inserted in the opening ofthe motor power test adapter.

4. Input a delivery rate of 200 ml/h.

5. Select pressure stage according to the TSC and start infusion.Read off value on the syringe gauge upon an alarm and compare with the specifications in the TSC.

Functional Inspection Power Supply SP Mechanical Inspection

1. Connect power supply to a Space system device and check the lock for proper function.

Functional Check

1. The device connected operates correctly after being switched on.

Perfusor® Space, 1.0 gb 7 — 5

Procedural Instructions on the TSC 7

1.0

For your notes:

7 — 6 Perfusor® Space, 1.0 gb

81.2

8 -Test Equipment and Special Tools

Test Equipment Designation Ord. No.

For Device Check

Syringe 2 ml / 3 ml

Syringe 10 ml

Syringe 30 ml

Service connector SP . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1062

HiBaSeD Service-CD . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 3301

Diameter gauge kit PSP . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5166Diameter gauge 32.0 mmDiameter gauge 23.4 mmDiameter gauge 15.5 mmDiameter gauge 9.0 mm

Length gauge PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5190

Fig.: 8 — 1 Diameter gauges

Fig.: 8 — 2 Length gauge

Perfusor® Space, 1.2 gb 8 — 1

Test Equipment and Special Tools 8

1.1

Syringe gauge PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5204Syringe gauge “#Lehre OPS 50“with push-button plate andmotor power test adapter for Perfusor® Space

For the TSC

Syringe 2 ml / 3 ml

Syringe 30 ml

Measuring instrument for electrical safety

Service adapter SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5174for electrical safety

Service connector SP . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1062

Syringe gauge PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5204Syringe gauge “#Lehre OPS 50“with push-button plate andmotor power test adapter for Perfusor® Space

Fig.: 8 — 3 Syringe gauge

Fig.: 8 — 4 Motor power test adapter

8 — 2 Perfusor® Space, 1.1 gb

Test Equipment and Special Tools 8

1.2

Special Tools Designation Ord. No.

For Repairs

TORX screwdriver kit5 — 10, 25

TORX plus screwdriver kit5 — 10, 25

Screwdriver 6IPx60 TORX plus . . . . . . . . . . . . . . . . . . . 4002 4806

Screwdriver 8IPx60 TORX plus . . . . . . . . . . . . . . . . . . . 4002 4814

Screwdriver 10IPx60 TORX plus . . . . . . . . . . . . . . . . . . 4002 4822

Perfusor® Space, 1.2 gb 8 — 3

Test Equipment and Special Tools 8

1.0

For your notes:

8 — 4 Perfusor® Space, 1.0 gb

91.2

9 -Spare Parts List

Item Designation Ord. No.

Perfusor® Space Service part kit Perfusor® Space . . . . . . . . . . . . . 3477 4270with:housing cover cap (40 pieces)cover caps for operating unit (10 pieces)cover cap for syringe holder (10 pieces)cover cap for drive head and claw (20 pieces)housing foot (20 pieces)release button SP with leaf spring (5 pieces)wing sensor holder (2 pieces)locking clip for piston brake (10 pieces)PCA key (2 pieces)

Cover caps for housing SP (50 pieces) . . . . . . . . 3477 4386

Cover caps for operating unit PSP (50 pieces) . 3477 3103

Connector seal P2 (50 pieces) . . . . . . . . . . . . . . . 3477 3102

Screw kit Perfusor® Space . . . . . . . . . . . . . . . . . . 3477 4289with:screw EJOT 22×8 WN 5451 TORX 6IP (5 pieces)screw EJOT 25×7 WN 5451 TORX 8IP (5 pieces)screw EJOT 30×6 WN 5451 TORX 10IP (5 pieces)screw EJOT 30×8 WN 5451 TORX 10IP (10 pieces)screw EJOT 20×12 WN 5452 TORX 6IP (5 pieces)screw EJOT 20×14 WN 5452 TORX 6IP (5 pieces)screw EJOT 22×4.5 WN 5452 TORX 6IP (10 pieces)screw EJOT 25×10 WN 5452 TORX 8IP (5 pieces)screw EJOT 30×8 WN 5452 TORX 10IP (10 pieces)screw EJOT 30×12 WN 5452 TORX 10IP (10 pieces)screw EJOT 30×35 WN 5452 TORX 10IP (5 pieces)screw EJOT 22×8 WN 5454 TORX 6IP (5 pieces)locking ring (5 pieces)

Perfusor® Space, 1.2 gb 9 — 1

Spare Parts List 9

1.1

Fig.: 9 — 1 Exploded drawing Perfusor® Space

1

2

3

4 5 67

8

10

9

11

12

13

14

17

18

1819

21

22

23

15

16

9 — 2 Perfusor® Space, 1.1 gb

Spare Parts List 9

1.1

1 Battery compartment cover PSP . . . . . . . . . . . . . 3452 0872

2 Battery pack SP (NIMH) . . . . . . . . . . . . . . . . . . . . 0871 3180

3 Operating unit PSP . . . . . . . . . . . . . . . . . . . . . . . 3452 0970

4 Hinge plate PSP, left . . . . . . . . . . . . . . . . . . . . . . 3452 1011

5 Hinge plate PSP, right . . . . . . . . . . . . . . . . . . . . . 3452 1020

6 PCA-slide PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0899

7 PCA-eccentric PSP . . . . . . . . . . . . . . . . . . . . . . . . 3452 0902

8 Rear panel, operating unit PSP . . . . . . . . . . . . . . 3452 1003

9 LC display SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0988

10 Front flap with keyboard PSP. . . . . . . . . . . . . . . . 3452 0996

11 Upper part of housing PSP . . . . . . . . . . . . . . . . . 3452 0910

12 Loudspeaker SP . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0937

13 Drive PSP, cpl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1046

14 Drive head PSP . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1038(incl. driving tube)

15 Claw mechanism PSP . . . . . . . . . . . . . . . . . . . . . 3452 1550

16 Drive PCB, PSP. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 1569

17 Side part of housing PSP . . . . . . . . . . . . . . . . . . . 3452 1054

18 Piston brake PSP ribbon cable . . . . . . . . . . . . . . . 3452 0864

19 Syringe holder with piston brake PSP, cpl. . . . . . 3452 0945

20 Syringe holder PSP spring. . . . . . . . . . . . . . . . . . . 3452 0953

21 Piston brake PSP guide rail . . . . . . . . . . . . . . . . . 3452 0961

22 Processor PCB PSP . . . . . . . . . . . . . . . . . . . . . . . . 3452 0880(incl. connectors andsyringe wing sensor)

23 Housing bottom part PSP . . . . . . . . . . . . . . . . . . 3452 0929

Type plate PSP . . . . . . . . . . . . . . . . . . . . . . . . . Upon request

Perfusor® Space, 1.1 gb 9 — 3

Spare Parts List 9

1.0

9 — 4 Perfusor® Space, 1.0 gb

101.2

10 -Revision Documentation

Description of Version Version 1.0 (Base Version)

— First version of this Service Manual

— Release date: 07.01.05.

Version 1.1

— Description for disassembly of the drive head added.

— Claw mechanism and drive head PCB added as new spare parts.

— Description of the Service Program HiBaSeD changed to new version 1.5.0.

— Release date: 20.03.06

Version 1.2

— New kinds of power supplies.

— Changed TSC of the power supply.

— Changed service part kit and screw kit.

— Release date: 02.04.07

Version List of the Individual Pages

Perfusor® Space, 1.2 gb 10 — 1

Revision Documentation 10

1.0

10 — 2 Perfusor® Space, 1.0 gb

10

1.2

Title and Leading Pages

Page 0 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 0 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 0 — 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 0 — 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Chapter 1 «System Overview»

Page 1 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 1 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 1 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 1 — 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 1 — 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 1 — 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Chapter 2 «Unit Diagnosis / Calibration»

Page 2 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 2 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 2 — 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 2 — 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 3 «Disassembly / Assembly»

Page 3 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Perfusor® Space, 1.2 gb 10 — 3

10

1.2

Page 3 — 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 3 — 45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 3 — 49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 3 — 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 4 «Servicing the Unit»

Page 4 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 4 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 5 «Technical Safety Check (TSC)»

Page 5 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 5 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Chapter 6 «Technical Safety Check (TSC)»

Page 6 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 6 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 7 «Procedural Instructions on the TSC»

Page 7 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 7 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 7 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 7 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 7 — 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Page 7 — 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 8 «Test Equipment and Special Tools»

Page 8 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 8 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 8 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 8 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 9 «Spare Parts List»

Page 9 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 9 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 9 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.1

Page 9 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 10 «Revision Documentation»

Page 10 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 10 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

10 — 4 Perfusor® Space, 1.2 gb

10

1.2

Page 10 — 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 10 — 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 10 — 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 10 — 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.0

Chapter 11 «Index»

Page 11 — 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Page 11 — 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Version 1.2

Perfusor® Space, 1.2 gb 10 — 5

10

1.0

10 — 6 Perfusor® Space, 1.0 gb

111.2

11 -Index

A

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 12

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 1, 3 — 35

B

Battery compartment cover . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 9

Battery module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 9

Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 — 1

Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 5

C

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 14

Procedural instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 14

Checks after repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 47

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 — 1

Compatibility list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 11

Current versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 — 5

D

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 1

Device check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 9

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 1

Drive

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 45

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 20

Drive head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 21

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 44

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 24

E

Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 3

Error modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 8

F

Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 3

H

Housing

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 46

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 17

Housing upper part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 17

I

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 1

L

List of abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 — 9

Loudspeaker

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 43

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 19

O

Operating unit

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 47

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 12, 3 — 15

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 12

P

Physical construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 2

Piston brake

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 43

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 27

Processor PCB

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 36

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 34

R

Release button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 19

Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 — 6

Revision service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 — 5

S

Service Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 7

Servicing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 — 1

Side part of housing . . . . . . . . . . . . . . . . . . . . . . . . 3 — 23, 3 — 45

Perfusor® Space, 1.2 gb 11 — 1

Index 11

1.2

Software update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 6

Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 — 1

Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 — 1

Syringe holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 27

System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 1

T

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 12

Technical Safety Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 — 5

Perfusor® Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 — 1

Power supply SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 — 1

Test equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 — 1

Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 — 29

TSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 — 5

Perfusor® Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 — 1

Power supply SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 — 1

Procedural instructions . . . . . . . . . . . . . . . . . . . . . . . . . 7 — 1

Test equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 — 2

U

Unit foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 — 11

Unit software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 — 6

11 — 2 Perfusor® Space, 1.2 gb